Klein Tools for Linemen Electricians Mechanics : Catalog No. 39 : Issued March 1939

for

LINEMEN
ELECTRICIANS
MECHANICS

CATALOG No. 39

Issued March 1939

GENUINE KLEIN TOOLS

KLEIN PLIERS

All Klein Pliers are hammer forged from
high grade tool steel made specially to our
analysis.

Every plier is individually fitted, tempered,
adjusted and tested. (The test in every case
being far in excess of any pressure that could
be applied by hand).

Klein Pliers are the established standard in
the electrical industry and have equal accept¬
ance with the men on steel construction and

reinforced concrete work because they far
outlast the ordinary commercial tool.

In general manufacturing wherever Klein
Pliers are used Klein Quality is relied upon
to increase production and reduce cost.

We guarantee all Klein Tools against defects
in material or workmanship ( ), but

this does not mean they are indestructible.
When properly used, Klein Tools will give
years of service.

KLEIN'S SIDE CUTTING PLIER

N.E. Type {"Stream-lined") With Sleeve-Joint Twister

These pliers are identical with Series
201-N.E. but have opening provided
for twisting double tube sleeve joints.

♦Sleeve opening in 6' and V pliers for
Nos. 14 and 17 N.B.S. and No. 12 B. ft
S. (.045.)

CAT. No. SIZE

*212-6 N.E. 6-inch
*212-7 N.E. 7-inch
*212-8 N.E. 8-inch

No.2l2-N.E.

WEIGHT PER DOZ.

.51/4 lbs.

.7% lbs.

.lb*-

(This series of pliers can be modified with meter seal instead of sleeve openings to order only.)

KLEIN'S OBLIQUE CUTTING PLIER

Electricians, telephone men and
switchboard builders will find this
particular oblique cutting plier one
of the most useful tools in their kits.
Cuts close, the narrow head permit¬
ting its use in confined places. The
knives are perfectly fitted, so that
they meet accurately at all points.

No. 202

CAT. No. SIZE WEIGHT PER DOZ.

202-5 5-inch .3% Ibt.

202-6 6-inch . * lb*.

KLEIN'S OBLIQUE CUTTING PLIER

This plier measures exactly 5 inches
in length. It is slightly smaller in all
dimensions than the 202-5 and will be
found particularly convenient as it
can easily be carried in vest pocket.
For electricians, telephone men and
switchboard builders.

CAT. No. SIZE

245-5 5-inch

No. 245

WEIGHT PER DOZ.

.3 lb*.

A few drops of light oil at the hinge now and then will keep your pliers
working smoothly and prevent undue wear.

All Pliers, Polithed Heads and Handles Temper Blued. Standard Package 6 in a box.

KLEIN'S SIDE CUTTING PLIER

No. 201

CAT. No. SIZE

201-5 5-inch
201-6 6-inch
201-7 7-inch
201-8 8-inch
201-9 9-inch

WEIGHT PER DOZ.

.... 3 lbs.
. . . . 51/4 lb*.

. . . . 71/4 lb*.

. . . . 11% lb*.

. . . .14 lb*.

For use on bare and insulated wire.
For linemen, electricians and mechan¬
ics. Adaptable for all uses where a
high quality plier of this type is re¬
quired.

Genuine Klein Linemen’s Side Cut¬
ting Plier is one of the most popular
pliers in use today. Its handles are
shaped to the curvature of the hand,
a much desired feature. Powerful
leverage and keen reinforced cutting
knives make this plier adaptable for
heavy cutting.

Full clearance back of the knife per¬
mits use on insulated wire.

KLEIN'S SIDE CUTTING PLIER

With Sleeve-Joint Twister

CAT. No. SIZE

*212-6 6-inch
*212-7 7-inch
*212-8 8-inch

No. 212

WEIGHT PER DOZ.

. . . . 51/4 lb*.

. . . . 7% lb*.

. . . . 11% lb*.

For use on bare and insulated wire.
For linemen and electricians. Special¬
ly designed for telegraph and tele¬
phone work.

This plier is the same as No. 201 se¬
ries, but with opening provided for
twisting double tube sleeve joints.

-Sleeve opening in 0 ana / pners
Nos. 14 and 17 N.B.S. and No. 12 B.
(.045.)

♦Sleeve opening in 8" pliers for No. 12
N.B.S. and No. 10 B. & S. (.104.)

KLEIN'S OBLIQUE CUTTING PLIER

With "W" Stripping Notches

This tool has two “W” shaped
notches at back of the cutting knives.
Specially designed for removing ace¬
tate cellulose insulation from .050
and .058 wires used on telephone dis¬
tributing frames, etc.

KLEIN'S OBLIQUE CUTTING PLIER

With Wire Stripping Notch and Sleeve Openings

No. 240-S

CAT. No. SIZE WEIGHT PER DOZ.

240-5-S 5-inch.3% lb*.

This plier is same as 202 series but
with addition of stripping notch and
openings for twisting sleeves. Made
in one size only.

Another use for the notch is that it
provides a means for “crimping” on
.032—.025 single tube copper sleeves
often used in telephone work for
splicing .032 bridle wire and .025 in¬
side wire. When so used make two
“crimps” at each end of sleeve for
.032 bridle wire and three “crimps”
for .025 inside wire.

(This series of pliers can be modified with meter seal instead of sleeve openings to order only.)

KLEIN'S SIDE CUTTING PLIER

N.E. Type ("Stream-Hned")

CAT. No.

SIZE

WEIGHT PER DOZ.

201-5 N.E.

5-inch . . . .

.3 lb*.

201-6 N.E.

6-inch . . . .

.51/4 lbs.

201-7 N.E.

7-inch . . . .

201-8 N.E.

8-inch . . . .

.11% lbs.

201-9 N.E.

9-inch . . . .

.I3y 2 lbs.

For use on bare and insulated wire.
For linemen, electricians and mechan¬
ics. Adaptable for all uses where a
high quality plier of this type is re¬
quired.

These pliers are identical with Series
201 except that the nose is round to
permit working in confined space and
all edges are rounded to prevent
nicking of wire.

Full clearance back of the knife per¬
mits use on insulated wire.

KLEIN'S OBLIQUE CUTTING PLIER

With Wire Stripping Notch

No. 240

This plier is identical with the No.
202 series with the addition of a notch
in the cutting knives for stripping
small wires. The notch is placed 3/16
inch from hinge and has diameter of
.052 inch and can be used for “crimp¬
ing” single tube copper sleeves as de¬
scribed under No. 240-S above.

CAT. No. SIZE

240-5 5-inch
240-6 6-inch

WEIGHT PER DOZ.

. ... 3% lb*.
. ... 4 lbs.

All Fliers, Polished Heed* and Handles Temper Blued. Standard Package 6 in a box.

AH Pliers, Polished Heads and Handles Temper Blued. Standard Packaqe 6 in a box.

2

GENUINE KLEIN TOOLS

KLEIN'S OBLIQUE CUTTING PLIER

With "W" Stripping Notches, Sleeve Openings and Skinning Hole
(Bell System Type)

This plier is the all-purpose cutting
tool for telephone installation and
maintenance work. The “W” notches
will slit acetate cellulose and other
insulations from wires up to .058 O.D.
A stripping hole .052 diameter is pro¬
vided in blades. Sleeve openings in
handles.

Another use for the notch is that it
provides a means for “crimping” on
.032—.025 single tube copper sleeves
often used in telephone work for
splicing .032 bridle wire and .025 in¬
side wire. When so used make two
“crimps" at each end of sleeve for
.032 bridle wire and three “crimps”
for .025 inside wire.

No. 202-SW

CAT. No. SIZE

202-5-SW 51/2-inch

WEIGHT PER DOZ.

. . . . 3% lb.-

KLEIN'S NARROW NOSED OBLIQUE CUTTING PLIER

This plier has narrow hinge and
pointed nose, enabling convenient use
in confined space. The knives are per¬
fectly matched for clean cutting.
Much used in telephone and radio
work.

No. 202-A

CAT. No. SIZE WEIGHT PER DOZ.

202-5-A 5-inch.3% lbs.

202-6-A 6-inch.4 lb*.

KLEIN'S OBLIQUE CUTTING PLIER

Heavy Duty Pattern

This plier is similar in construction
to the No. 202 that has been a favorite
with mechanics for many years. It is,
however, made heavier to meet the re¬
quirements of those desiring a strong¬
er plier for general work. It will be
found particularly useful where it is
not necessary to reach into closely
confined spaces.

WEIGHT PER DOZ.

. . . . 41/4 lbs.

KLEIN'S LONG NOSE PLIER, WITHOUT CUTTERS

This style of plier has been perfected
to meet a long-felt want of the elec¬
trician and general mechanic. Special
features are its adaptability to strip¬
ping the ends of insulated wire and
the extra long reach of the jaws
which permits getting into difficult
places. For switchboard, telegraph
and telephone work, armature wind¬
ing, etc. This tool is especially hard¬
ened and tempered to insure positive
grip at point of nose when pressure
is applied. Point 3/32 in. round.

♦This plier has extra long nose—measur¬
ing 234" from center of hinge to point.

No. 301

CAT. No. SIZE

301-5 5-inch
301-6 6-inch
*301-7 7-ineh

WEIGHT PER DOZ.

. . . . 31/4 lbs.

. . . . 3% lbs.

. . . . 41/4 lbs.

NOTE: No. 301 series supersedes former No. 316 series (Bell System Type).

KLEIN'S LONG NOSE, SIDE CUTTING PLIER

Has the same features as No. 301
series shown above, with the addition
of the cutting knives. The knives are
carefully fitted and the body of the
plier is hardened and tempered, assur¬
ing true cutting. Point 3/32 in. round.

♦This plier has extra long nose—measur¬
ing 2?4" from center of hinge to point.

No. 203

CAT. No. SIZE WEIGHT PER DOZ.

203-5 5-inch. 3 Wa lbs.

203-6 6-inch. 3 % bs.

*203-7 7-inch.4'/, lbs.

KLEIN'S LONG NEEDLE NOSE PLIER

This tool has all the features of No.
301 series, with the exception that the
points of the nose are of the needle
point pattern, which some mechan¬
ics prefer. The thin points make
these pliers more useful for the gen¬
eral class of work done in Central
Offices. Point 1/16 in. round.

No. 303

CAT. No. SIZE WEIGHT PER DOZ.

303-6 6-inch .3% lbs.

KLEIN'S "AUTO" OBLIQUE CUTTING PLIER

"Handform" Handles

No. 220

CAT. No. SIZE WEIGHT PER DOZ.

220-7 7-inch.7 lbs.

Made especially for automotive me¬
chanics and others who demand a
high quality plier of this pattern.
The knives are close cutting and care¬
fully matched for their full length.
Useful for pulling cotter pins, for
choke wires etc. The “Handform”
handles provide full leverage and
comfort for continual use.

KLEIN'S CHAIN NOSE PLIER, WITHOUT CUTTERS

CAT. No. SIZE

317-6 6-inch

No. 317

WEIGHT PER DOZ.

.3l/ 2 lbs.

This plier is intended for general use
where a shorter nose is desirable.
Made in one size only—6 inch.

KLEIN'S END CUTTING PLIER

A generally useful end cutting plier
for electrical mechanics. Has stout
jaws and broad cutting knives. There
is ample room in the throat of pliers
when needed. Frequently used for en¬
closed work which cannot be reached
with the oblique type of cutter.

♦The 7" size has “handform” handles as
used on our side cutting pliers.

KLEIN'S CHAIN NOSE PLIER, SIDE CUTTING

WEIGHT PER DOZ.

. . . . 31/2 lbs.

A chain nose plier similar to No. 317-
6 but with side cutting knives. The
knives are carefully matched and cut
true over their entire length. Made
in one size only—6 inch.

KLEIN'S DIAGONAL CUTTING PLIER

With Raised Knives

WEIGHT PER DOZ.

. . . . 31/4 lbs.

This plier has perhaps as many uses
as the oblique pattern. It has long cut¬
ting knives well matched, so as to
permit close and clean cutting. The
head is narrow to penetrate confined
places and work between binding
posts, etc. The knives are correctly
constructed to cut clean and to give
lasting service.

KLEIN'S HEAT-COIL PLIER

No. 313

CAT. No. SIZE WEIGHT PER DOZ.

313-6 6-inch .3% lbs.

Particularly adapted for the remov¬
ing of heat coils from switchboards
and telephone terminals, the points
of the nose being shaped to fit the
coils. This tool is also serviceable in
removing caps from batteries or from
binding posts, as well as holding any
cylindrical object.

All Pliers, Polished Heads and Handles Temper Blued. Standard Package 6 in a box.

All Pliers. Polished Heads and Handles Temper Blued. Standard Package 6 in a box.

3

GENUINE KLEIN TOOLS

KLEIN'S LONG FLAT NOSE PLIER

Extra long wide flat nose makes this
an especially useful plier. This plier
is hardened and tempered, so that
the jaw will not spring when pres¬
sure is applied. This tool is adapt¬
able to switchboard work, telephone
and telegraph work, armature wind¬
ing, etc. A very handy tool for
spring adjusting. This plier can be
supplied with inside of jaws left
smooth if desired.

CAT. No. SIZE WEIGHT PER DOZ.

305-6 6-inch.31/j lbs.

KLEIN'S LONG NOSE SLEEVE PLIER

(Bell System Type)

This plier is identical with No. 301-6
but with the addition of sleeve open¬
ings for twisting No. 17 N.B.S. and
smaller copper sleeves. Particularly
useful for telephone work. Point 3/32
in. round.

No. 316-S

CAT. No. SIZE WEIGHT PER DOZ.

316-S 6-inch.3% lbs.

KLEIN'S LONG FLAT NOSE, SIDE CUTTING PLIER

This plier is similar in its usefulness
to No. 305 series with the added
advantage of cutting knives.

No. 206

CAT. No. SIZE WEIGHT PER DOZ.

206-6 6-inch.3|/j lb*.

KLEIN'S LONG NOSE CORD CRIMPING PLIER

This plier is same as 301-6 with addi¬
tion of an oval groove for crimping
telephone cords. A great convenience
in telephone switchboard work. Point
3/32 in. round.

No. 301-C

CAT. No. SIZE WEIGHT PER DOZ.

301-C 6-inch.3% lb*.

KLEIN'S LONG FLAT NOSE, SPRING ADJUSTING PLIER

This plier is hollow ground on the
outside of the jaws to reach between
and grasp springs easily. It is largely
used by telephone men because it
makes rapid and accurate adjustments
possible.

No. 311

CAT. No. SIZE WEIGHT PER DOZ.

311-51/2 51/j-inch.3ft lb*.

KLEIN'S CORD TIP CLOSING PLIER

The jaws of this tool are of sturdy
design to permit its use as a hand
press for closing cord tips such as
W.E. 101 and 102. The circular open¬
ing in the jaws is correctly sized to
ensure a perfect connection when the
closure is completed.

WEIGHT PER D

KLEIN'S LONG DUCK BILL PLIER

No. 304

CAT. No. SIZE

304-6 6-inch

WEIGHT PER DOZ.

. . . . 3l/ 2 lb*.

This plier is fitted with duck bill jaws
wider and heavier than those of the
ordinary flat nose plier. This affords
a tool with a firmer gripping surface.
Also in general use as a weaver’s plier.

KLEIN'S LONG DUCK BILL, SIDE CUTTING PLIER

This type is the same as No. 304
duck bill, with the addition of cutting
knives. As on all Klein Pliers, the
cutters are carefully fitted so as to
cut easily and true.

No. 205

CAT. No. SIZE WEIGHT PER DOZ.

205-6 6-inch.3>/ 4 lb*.

KLEIN'S LONG CURVED NOSE PLIER

No. 302

CAT. No. SIZE WEIGHT PER DOZ.

302-6 6-inch.3>/ 4 lb*.

A handy plier for working around
switchboards, terminals and tele¬
phones, due to the nose being curved.
The angle is arranged to give full
clearance and prevent skinning of
knuckles. Users will find this tool
adaptable to a great variety of uses.
The jaws will not lose their shape or
set due to pressure applied, owing to
the quality of steel used, its harden¬
ing and tempering.

KLEIN'S HEAVY DUTY LONG NOSE CUTTING PLIER

No. 203-8

CAT. No. SIZE WEIGHT PER DOZ.

203-8 8-inch.8 lb*.

A long round nose cutting plier for
heavier gauge wires as used on ele¬
vator control boards etc. The round
nose 234 in. long is for forming loops.
A flat space ahead of the knife holds
objects securely, will also “crack”
insulation conveniently. The “hand-
form” shaped handles afford maxi¬
mum comfort and powerful leverage.

KLEIN'S HEAVY DUTY LONG NOSE CUTTING PLIER

With Stripping Notch

This plier is same as No. 203-8 de¬
scribed above with the addition of a
stripping notch in the knives. This
notch is regularly furnished for No.
12 B. & S. insulated wire, but can be
made for other sizes to order.

No. 203-8N

CAT. No. SIZE WEIGHT PER DOZ.

203-8N 8-inch.8 lb*.

The following pliers fitted with spring opening handles are special pattern* for bench work on
radio sets, radio tubes, switchboards, distributing frame* and other production work for which
they may be suited. The springs fitted serve to keep pliers open in position ready for immediate
use without the necessity of opening up by hand—a time saver and convenience.

KLEIN'S LONG NOSE PLIER

(Volute Spring—With 1 / 4 " Knife at Point)

A plier designed to provide for light
cutting in spaces beyond the reach of
regular cutting pliers. Largely used
in manufacturing and servicing of
radio sets.

No. 301-6-VP

CAT. No. SIZE WEIGHT PER DOZ.

301-6-VP 6-inch.4 lbs.

All Pliers, Polished Heads and Handles Temper Blued. Standard Package 6 in a box.

All Pliers, Polished Heads and Handles Temper Blued. Standard Package 6 in a box.

4

GENUINE KLEIN TOOLS

KLEIN'S OBLIQUE CUTTING PLIER

(Volute Spring—Narrow Tapered Head)

This plier is especially useful for
light cutting in confined spaces.
Largely used in radio tube shops.
Volute spring keeps plier open.

No. 202-5-VO

CAT. No. SIZE WEIGHT PER DOZ.

202-5-VO 5l/ r inch .3% lb*.

KLEIN'S OBLIQUE CUTTING PLIER

(Volute Spring—Cutout Knives)

A tool specially designed for cutting
at tip only with balance of knife re¬
moved, thus providing a space J4*inch
wide to clear any interfering obstruc¬
tion. (Largely used on radio tube con¬
struction.) Volute spring keeps plier
open for use.

No. 202-5-VC

CAT. No. SIZE WEIGHT PER DOZ.

202-5-VC 5l/ 2 -inch .3% lbs.

KLEIN'S SLIP JOINT PLIER

Made of tempered tool steel (like all
Klein Pliers) this tool will give serv¬
ice that cannot be expected from the
ordinary plier of similar pattern. Has
a wire cutter and a screwdriver han¬
dle.

No. 406

CAT. No. SIZE WEIGHT PER DOZ.

406-6 ( / 2 6 l /2-inch.6 lbs.

KLEIN'S "UTILITY" SLIP JOINT PLIER

The special features of this plier,
which is of the heavy duty type, are
adaptability as a pipe wrench and
wire cutter. Has sure grip jaws which
readily accommodate objects of ir¬
regular shape. It is also made of tem¬
pered tool steel like the item above.

KLEIN'S BENT NOSE SLIP JOINT PLIER

No. 407

CAT. No. SIZE WEIGHT PER DOZ.

407-7 7-inch.6>/| lbs.

KLEIN'S OBLIQUE CUTTING PLIER

(Volute Spring—Narrow Head)

This is the regular No. 202-5-A Plier
but fitted with volute spring for
bench work. It is suitable for heavier
cutting than the No. 202-5-VO and
should be used where the working
space permits.

No. 202-5-AV

CAT. No. SIZE WEIGHT PER DOZ.

202-5-AV 5l/ 2 -?nch.4 lbs.

A plier of the bent nose type. Spe¬
cially designed for use in difficult
places. An excellent general purpose
tool that should be included in every
mechanic’s kit. Made of tempered
tool steel and can be relied on for
maximum service. (Sometimes refer¬
red to as Bent Nose Gas Plier.)

NOTE:—The slip joint pliers shown on this page are made of tool steel and tempered throughout which
enables them to resist the corrosive action of acids around battery work much longer than the cheaper
grades of similar pattern.

No. 408

CAT. No. SIZE WEIGHT PER DOZ.

408-8 8-inch.7l/ 2 lbs.

KLEIN'S OBLIQUE CUTTING PLIER

(Volute Spring)

This is the regular 245-5 plier, but
fitted with volute spring for cutting
in general bench production work.

CAT. No. SIZE WEIGHT PER DOZ.

245-5-V 5-inch.3 lbs.

KLEIN'S LONG NOSE PLIER, WITHOUT CUTTING KNIVES

(Volute Spring)

For bench work where a plain long
nose plier is required. The spring
keeps plier open at position ready for
immediate use.

No. 301-5-V

CAT. No. SIZE WEIGHT PER DOZ.

301-5-V 5-inch.3'/ 2 lbs.

KLEIN'S LONG NOSE CUTTING PLIER

(Volute Spring)

A convenient tool for production
bench work where a combination of
long jaws with cutting knives is re¬
quired. Fitted with volute spring.

No. 203-5-V

CAT. No. SIZE WEIGHT PER DOZ.

203-5-V 5-inch.3*/ 2 lbs.

All Pliers, Polished Heads and Handles Temper Blued. Standard Package 6 in a box.

KLEIN'S SPLICING CLAMPS

Of all the tools in use, the lineman’s splicing
clamp is one of the most abused, for in the
absence of .omething more appropriate, the
splicing clamp often serves as hammer,
wrench or crow bar and then again it must
be of service in making dependable electrical
and mechanical joints. It is obvious that not
“any old thing” is profitable. Apart from the
abuse-resisting qualities, the tool must be
properly proportioned, the jaws must be
properly tempered and hardened so as to

resist wear, the handles must be resistant
to bending strain and retain their normal
set, and the dies for holding the wires and
sleeves must fit. To all this especial attention
is given in Klein Splicing Clamps.

The entire range of sleeve and wire sizes
practical for this type of tool are included in
the Klein Splicing Clamps listed on the fol¬
lowing pages, which comprise the combina¬
tions most suitable for the work for which
they are intended.

A few drops of light oil at the hinge occasionally will keep your clamps
working smoothly as well as add to their life.

5

GENUINE KLEIN TOOLS

KLEIN'S SPLICING CLAMPS

No. 102-1

This clamp is arranged with five round holes for bare wire.

A handy pocket size, adapted especially for
telephone troublemen. The openings cover
wire sizes in general use.

Copper wire Nos. 8, 10, 12, 14, 16, B. & S.
Iron wire Nos. 10, 12, 14, 16, 18, B. W. G.

CAT. No. SIZE WEIGHT PER DOZ.

102-1 8-inch.5% lbs.

No. 102-3 and No. 102-30

For bare wire, arranged with five round holes and one oval hole.

CAT. No. SIZE WEIGHT PER DOZ.

102-3 10%-inch.16% lbs.

Copper wire Nos. 2, 4, 6, 8, 10, 12, B. & S.

Iron wire Nos. 4, 6, 8, 10, 12, 14, B. W. G.

(For nma wires but boles reversed. See No. 102-30)

CAT. No. SIZE WEIGHT PER DOZ.

102-30 10%-inch.16% lbs.

Copper wire Nos. 2, 4, 6, 8, 10, 12, B. & S.

Iron wire Nos. 4, 6, 8, 10, 12, 14, B. W. G.

(For seme wires but holes reversed. See No. 102-3)

Used in telephone, telegraph and
power line work, covering a wide
range of wires. Large hole can also
be used in serving guy wire or mes¬
senger strand, and is sometimes used
for No. 4 copper sleeves. The dies fit
the wires snugly to insure perfect
mechanical and electrical joints.

In the 102-3 the large hole is at the
hinge. In the 102-30 the holes have
been reversed, to meet the require¬
ments of those prefering this arrange¬
ment.

No. 102-48

This clamp has five openings for twisting bare copper wire.

Designed to meet the general range
of wire sizes used by Electric Light
and Power Companies.

The largest hole is also convenient to
bring together the guy strand before
applying a three bolt clamp.

Copper wire Nos. 0, 2, 4, 6 and 8, B. & S.

KLEIN'S COMBINATION WIRE AND SLEEVE CLAMPS

CAT. No. SIZE

132-15 111/,-inch

No. 132-15

For General Telephone Line Work

WEIGHT PER DOZ.

. . . .18 lbs.

Copper wire Nos. 4, 6, 8, 10, 12, B. & S.
Iron wire Nos. 6, 8, 10, 12, 14, B. W. G.
Oval hole .437 x .624.

Copper sleeves Nos. 6, 8, 10, 12, 14, 17, B. & S.
Iron Sleeves Nos. 8, 10, 12, 14, 16, 19, B. W. G.

This clamp has five round holes for twisting
bare wire. One oval hole for guy strand, .437
x .624.

The reverse side has five double chambers

for twisting double tube sleeves.

This clamp covers complete range of wires
as usually handled by telephone and tele¬
graph linemen.

No. 132-46

For General Power and Light Line Work

CAT. No. SIZE

132-46 lM/4-inch.

Copper wire Nos. 4, 6, 8, 10, 12, B. & S.
Iron wire Nos. 6, 8, 10, 12, 14, B. W. G.
Oval hole .437 x .624.

WEIGHT PER DOZ.

.17% lbs.

Copper sleeves Nos. 4, 6, 8, 10, 12, B. & S.
Iron sleeves Nos. 6, 8, 10, 12, 14, B. W. G.

This clamp has five round holes for twisting
bare wire. One oval hole for guy strand, .437
x .624.

The reverse side has five double chambers
for twisting double tube sleeves.

This clamp is similar to No. 132-15 but is
arranged to take copper sleeves No. 4 to No.
12 B. & S. It is intended particularly for use
of power companies requiring this range of
sizes.

Sleeve openings modified for single (oval) tube sleeves to order.

KLEIN'S SPLICING CLAMPS

KLEIN'S COMBINATION WIRE AND SLEEVE CLAMPS

No. 105-15

For twisting double tube sleeves.

This is a convenient pocket size splic¬
ing clamp. The chambers are ar¬
ranged to fit the sleeves snugly so
that sleeves are not injured in twist¬
ing and insure perfect mechanical
and electrical joints.

Copper sleeves Nos. 8, 10, 12, 14, 17, B. & S.
Iron sleeves Nos. 10, 12, 14, 16, 19, B. W. G.

CAT. No. SIZE WEIGHT PER DOZ.

105-15 8-inch.5% lbs.

No. 105-17 (Type "B")

This clamp has five sets of

This clamp is intended for telephone,
telegraph and power line work. The
chambers are arranged to fit the
sleeves snugly so that sleeves are not
injured in twisting and insure perfect
mechanical and electrical joints.

chambers for twisting double tube sleeves

CAT. No. SIZE WEIGHT PER DOZ.

105-17 10%-inch.17 lbs.

Copper sleeves Nos. 6, 8, 10, 12 and 14, B. & S.
Copper sleeves Nos. 12, 14 and 17, N. B. S.

Iron sleeves Nos. 8, 10, 12, 14, 16 and 19, B. W. G.

No. 132-12

CAT. No. SIZE

132-12 9-inch.

Copper wire Nos. 6, 8, 10, 12, B. & S.

Iron wire Nos. 8, 10, 12, 14, B. W. G.
Copper sleeves Nos. 8, 10, 12, 14, 17, B. & S.
Iron sleeves Nos. 10, 12, 14, 16, 19, B. W. G.

WEIGHT PER DOZ.

... II lbs.

Standard telephone splicing clamp for gen¬
eral line and trouble work.

This clamp has four round holes for twisting
bare wire.

The reverse side has four double chambers
for twisting double tube sleeves.

No. 132-30

For Railroad Signal and Telegraph Work

No. 105-31 (Type "C")

This is a special clamp or sleeve
twister of the plier type.

The jaw being forward of the hinge
permits convenient use in confined

spaces. Much used in telephone work CAT Ng SIZE weight per doz.

by troublemen and installers. I0MI 8%-inch.5% lb*.

Three double chambers for twisting Nos. 10 and 12
B. & S. sleeves, Nos. 12, 14 and 17 N. B. S. sleeves.

CAT. No. SIZE

132-30 111/4-inch.

The sleeve openings are for N.B.S. and
B.W.G. sizes 9 and 8 respectively. The re¬
maining five openings cover the range of

WEIGHT PER DOZ.

. . . . 18 lb*.

wire sizes generally used on Railroad Signal
and Telegraph construction.

Hammer Forged from High Grade Tool Steel. Polished Head* and Handle* Temper Blued.

Hammer Forged from High Grade Tool Steel. Polished Head* and Handle* Temper Blued.

6

GENUINE KLEIN TOOLS

KLEIN’S "COPPERWELD" SLEEVE CLAMP

KLEIN'S "DI-STOCK" SLEEVE TWISTER

No. 132-48 (For Copperweld)

CAT. No. SIZE

132-48 11 •/j-inch

This clamp has four chambers for twisting 4A, 6A, 8A and 3 No. 12. These chambers

single tube (oval) sleeves used for mak- also accommodate single tube (oval) sleeves

ing joints on Copperweld conductors sizes as per following table.

4A Copperweld or No. 1 solid B. & S. or No. 2 strand B. & S. Copper

6A Copperweld or No. 3 solid B. & S. or No. 4 strand B. & S. Copper

8A Copperweld or No. 4 solid B. & S. or No. 5 strand B. & S. Copper

3 No. 12 Copperweld or No. 5 solid B. & S. or No. 6 strand B. & S. Copper

The swing latch provided holds the head might develop otherwise from bowing of

securely closed while joint is being twisted, handles when twisting the larger sleeves,

preventing any slippage or “burning” which

KLEIN'S STRAND AND WIRE HOLDING TOOL

No. 132-39

CAT. No. SIZE

132-39 111/4-inch

WEIGHT PER DOZ.

. . . . 18 lbs.

This tool serves as a temporary clamp to hold placing permanent clamps or splicing and
together two sections of strand or wire while serving. A real convenience and time saver.

Openings will fit:

tV' strand (16,000 lb. Bell System) -fo" strand ( 6,000 lb. Bell System)

%" strand (10,000 lb. Bell System) -fo" strand ( 2,200 lb. Bell System)

7/64" solid No. 12 B. W. G. Iron or No. 10 B. & S. Copper Wire
3/32" solid No. 13 B. W. G. Iron or No. 11 B. & S. Copper Wire

CAT. No. WEIGHT EACH

107-20 (for oval or double tube sleeves)

(copper or aluminum). V/ 4 lbs.

Length overall, 23l/ 2 in.

This tool supersedes previous No. 107-2
This tool has been improved by making the
handles tubular 7/ a ” diameter and threading
them onto the head. They can be readily at¬
tached or removed—a real convenience when

clearance is limited, also affording consider¬
able reduction in weight.

We recommend this Di-Stock for use on all
types and makes of sleeves from No. 4 B. & S.
Solid up to No. 3/0 B. & S. Strand. (For
larger sleeves see Di-Stock No. 107-34.)

Space between yokes is 3" —usually suffi¬
cient for three sleeve openings.

The head is readily tightened onto the sleeve
and securely held by means of a thumb nut
operating in the hinged yoke as illustrated.
The central position of the head makes for
ease in keeping the sleeve straight while the
joint is being twisted, besides providing
ample leverage.

These tools are held in blank and finished
with sleeve openings as ordered.

(See note regarding details of sleeve sizes
required with your order.)

This tool is similar to the Klein Di-Stock
Sleeve Twister No. 107-20 but is of heavier
construction for use on larger size sleeves.
Of ample capacity for sleeves No. 3/0 B. & S.
up to 500,000 c.m. B. & S. and corresponding
size aluminum. The handles are tubular 1^"
diameter and are attached to the head by
means of a quick acting thread. This ar¬
rangement makes it possible to remove either
of the handles quickly and easily when clear¬
ance is required.

A hand operated lock lever closes the head
easily on the sleeve and maintains it securely
in position while the joint is being made.
Distance between the yokes on the head is
approximately 4 inches, giving ample room for
two or even three sleeve openings of large
size. The head is forged from high grade
tool steel and is heat treated for maximum
toughness and wear.

We carry a stock of these tools in blank and
cut the openings to order as required.

(See note regarding details of sleeve sizes
required with your order.)

NOTE—There being no standard on sleeves, actual samples for which twisting tools are desired should
accompany order. When this cannot be done the following data MUST be furnished. (I) Trade name or
name of manufacturer. (2) Sleeve number or size. (3) Type of sleeve (oval, double-tube, etc.). (4) Size and
type of conductor sleeves will be used on.

KLEIN'S WIRE AND SLEEVE CLAMPS

No. 132-47

CAT. No. SIZE WEIGHT PER DOZ.

132-47 11 •/j-inch.18 lbs.

This clamp has five special chambers for
twisting single tube or oval (Memco) sleeves
Nos. 2, 4, 6 and 8 and No. .104.

These sizes cover the range most generally
used by Electric Light and Power Compan¬
ies. The chambers (or openings) are a modi¬
fied “figure 8” shape, giving a secure hold
which prevents “burning” the sleeve when
the joint is twisted.

The swing latch provided is necessary to
overcome any spring in the handle which
might otherwise develop in a tool of this
type when used on larger sleeves.

A stop in the hinge prevents the handles
from opening beyond the point convenient
for clamping on to the sleeve.

No. 132-74

CAT. No. SIZE

132-74 111/2-inch

This clamp has three special chambers for
twisting single tube or oval (Memco) sleeves
Nos. 2, 4 and 6. Also an oval (hog) hole .437
x .624 for guy strand.

The chambers (or openings) are a modified
“figure 8” shape, giving a secure hold which
prevents “burning” the sleeve when the joint
is twisted.

The swing latch provided is necessary to
overcome any spring in the handle which
might otherwise develop in a tool of this
type when used on the larger sleeves.

A stop in the hinge prevents the handles
from opening beyond the point convenient
for clamping on to the sleeve.

SAFETY AND COMFORT

Safety is the first and vital point in consider¬
ing Climbers.

The lineman going up a pole depends en¬
tirely on his spurs; he must continue to de¬
pend on them while working, often with both
hands in use, and he must depend on those
same spurs to bring him safely to the ground
again.

To assure the utmost dependability Klein
Climbers are forged from special steels and
are individually tempered under expert su¬
pervision.

The shanks and gaffs are individually tested to in¬
sure perfect riveting and temper.

The shape of Klein Climbers has been care¬
fully considered. It is the result of many
years’ experience and much practical sugges¬
tion from linemen. Bad fitting climbers cause

as much discomfort as ill fitting shoes. Klein
Climbers have flexible shanks and yield read¬
ily to the pressure of the leg, they do not
chafe. The gaff or spur is correct in shape,
set of angle and temper. It is riveted to the
leg iron securely.

Linemen in general recognize Klein Climb¬
ers as the standard.

Worn gaffs can be replaced by sending the
climbers to us. We require this to assure de¬
pendable workmanship and temper.

It is not good safety practice to continue us¬
ing climbers after the gaffs are worn to less
than 1inches long (measured on the under¬
side).

We cannot consider any claim for replace¬
ment of climbers on which the gaffs show
evidence of grinding, re-tempering or other
misuse.

Hammer Forged from High Grade Tool Steel. Polished Heads and Handles Temper Blued.

7

GENUINE KLEIN TOOLS

INSTRUCTIONS for Sharpening Gaffs (Spurs) on
KLEIN CLIMBERS

Incorrect

Correct

Incorrect Correct

1. Always use sharp file. NEVER grind to
a point on any kind of wheel as you are likely
to set up heat which will spoil the temper
of the gaff and make it dangerous to use.

2. Set climber in a vise with the gaff upper¬
most and the stirrup of the climber turned
down so that you can file from heel to point
of gaff. File toward the point and down to
the edges of the underside of the gaff. Re¬
move only sufficient material to make a good
point.

3. Do not make a needle point. File both
side slopes, but not the top of gaff, to even
rounded surfaces, so that the final point is
always in the top ridge of the gaff.

4. The underside of the gaff should be left
perfectly straight to within fa" of the point,
then rounded slightly toward the top ridge
of the gaff on a radius of *4". At a distance
fa" back from the point, you should have a
width of approximately fa" measured on the
underside of the gaff. The remainder of the
underside should be kept perfectly straight.

5. For safety, climbers should not be used
after the gaffs are worn or filed to 1*4"
long, measured on the underside of the gaff.
When climbers get in this condition, they
should be regaffed or a new pair obtained.
By following these simple instructions, a
satisfactory job can be secured and no un¬
necessary risks will be taken.

These instructions are printed in bulletin form for distribution. Furnished gratis.

KLEIN'S "LIGHTWEIGHT" LINEMEN'S CLIMBERS

No. 1903

Stock sizes 15, 15J4, 16. 16*4, 17, 17*4 and 18 inches, measured from the
instep to the end of shank. Other sizes to order. Every climber individually
tested.

These climbers are similar to No. 1900, but are made somewhat lighter in
the leg iron.

Gaffs 3)4 inches long measured on the outside.

WEIGHT PER PAIR

1903 Riveted Strap Loops. 2 V» ,b *-

No. 1903

KLEIN'S TREE CLIMBERS

No. 1907

These climbers are similar to the No. 1901 but are furnished with extra
long gaffs necessary to penetrate bark in tree climbing. The gaffs (or
spurs) are 5 ]/ 2 inches long, measured on the outside, and 3 inches long,
measured on the underside. They are set high in the leg iron so that the
points clear the ground when walking. These are the standard tree climbers
used by Forest Rangers, High Riggers, Fire Wardens and Surveyors.

Stock sizes 15, 15)4, 16, 16*4, 17, 17*4 and 18 inches, measured from the
instep to the end of shank. Other sizes to order. Every climber individually
tested.

CAT No WEIGHT PER PAIR

1907 Punched Strap Loops. 4 lbl -

No. 1907

(MOTE—In ordering climbers always mention the length of shank wanted. Measure from instep to the extreme
end of leg irons which should come I in. below the knee joint for comfort. The position of the gaff hole in
the leg iron makes it impracticable to interchange gaffs between linemen's climbers and tree climbers or
vice versa.

No. 1939

KLEIN'S "STREAMLINED" LINEMEN'S CLIMBERS

No. 1939

The design is new. The use of any unnecessary metal has been carefully
avoided. The leg irons are flexible and tapered in width and thickness. The
critical section from 3 inches above the gaff to half way across the stirrup
has been designed for ample strength.

The gaffs are slender type—preferred on treated (“Black Jack") poles. A
wrought ring carries the ankle strap.

These climber* are approximately one third lighter in weight than jtandard patterns
and about 10% lighter than the original "lightweight."

They offer every possible comfort and a full factor of safety.

Gaffs 3)4 inches long measured on the outside.

Stock sizes 15, 15)4, 16, 16)4, 17, 17)4 and 18 inches, measured from instep
to end of shank. Other sizes to order. Every climber individually tested.

CAT. No.

1939 Riveted Top Loop, Ring at Ankle

WEIGHT PER PAIR

. . . 2*/j lbs.

(With this Climber use Ankle Strap No. 5301-16 or No. 5301-26. See page 43.)

KLEIN'S STANDARD LINEMEN'S CLIMBERS

I

\J

No. 1900

No. 1900 and 1901

Stock sizes 15, 15*4, 16, 16*4, 17, 17*4 and 18 inches, meas¬
ured from the instep to the end of shank. Other sizes to
order. Every climber individually tested.

Gaffs 3 y 2 inches long measured on the outside.

CAT. No.

1900 Riveted Strap Loops

1901 Punched Strap Loops

WEIGHT PER PAIR

... 3% lbs.

. . . . 3% lbs.

No. 1901

NOTE—In ordering climbers always mention the length of shank wanted Measure from mstepto ^e extreme
end of leg irons which should come I in. below the knee joint for comfort. The position of the gaff hole in
the leg iron makes it impracticable to interchange gaffs between linemens climbers and tree climbers or

Drop Forged Tested
Hardware

The name “Mathias Klein & Sons” or the
Klein trade-mark on leather goods assures
quality and trustworthiness.

The very life of a lineman depends upon the
reliability of his belt and strap. First cost
is incidental—quality MUST be the best.
Klein’s leather is first quality “slow process”
vegetable tanned harness leather selected for
its strength and durability and checked by
chemical analysis and frequent laboratory
tensile tests.

The same skilled workmanship is evident on
those Belts and Safety Straps we list, where
“Klein-Kord" replaces leather. (For a de¬

scription of this special fabric see page 54.)
All genuine “Klein” "D” Rings, Snaps and
Buckles are drop forged from bar steel in our
own plant and individually tested to 1500 lbs.
All sewing is done with hot waxed genuine
Irish linen thread, lock stitched. Riveting
by hand with solid copper rivets.

“Klein” Belts and Straps are standard with
and exclusively specified by many of the
largest utility corporations, railroads, fire
departments, etc. in the country.

Write for special bulletins giving actual specifications, drawings and other vital information on the factor of
safety of Belts and Safety Straps. These are furnished gratis.

8

GENUINE KLEIN TOOLS

RULES FOR CARE OF LEATHER

KLEIN'S CLIMBER STRAPS AND PADS

It pays to give safety straps and tool belts proper attention. Below are
a few rules, which, if carefully followed, will give you service you have a
right to expect from Klein leather goods.

Go over leather at least once every 90 days and scrape out the “scale” that
forms whenever metal rubs against the leather. Examine for stretch, wear,
cracks and cuts.

Take a small quantity of *Neatsfoot oil on a rag and rub into the leather on
the hair side. Do not flush the oil on directly from the can—every inch of
the leather should be uniformly covered to keep it pliable and waterproof.

In storage particular care should be taken to keep belts and straps away
from direct or close contact with heat, such as steam coils, radiators or
stoves. Leather exposed to such conditions rapidly deteriorates and loses
its tensile strength. It becomes dry, brittle and unreliable. After exposure
to water or acid, belts and straps should be wiped off as quickly as possible
with an oily rag dipped in *Neatsfoot oil as before described.

Never dry damp or wet leather with the aid of heat. Such treatment
weakens the fiber of the leather, and may even destroy it if sufficient
temperature is used.

BEND TEST—This should only be made when leather contains sufficient
oil to make it soft and pliable. At room temperature bend the leather
slowly with the grain side out over a mandrel not less than Va inch » n
diameter through an angle of 180°. Do not bend at buckle holes in any
case. If leather of such thickness as necessary for Belts and Straps is
abused by abrupt bending without a mandrel, the leather may develop
cracks on account of the excessive strain put on the grain side. When tested
as directed above the leather should show no cracks although there may be
a slight opening up of the grain surface.

NOTE:—We will not replace any belt or strap which has been cracked or
broken on the grain side by “forced” bending.

NEATSFOOT OIL

♦For the convenience of our customers and to ensure the best grade, we
furnish genuine Neatsfoot oil in cans with full directions for use as follows -

CAT. No. WEIGHT PER DOZ.

N.O.-I Pint Can.15 lbs.

N.O.-2 Quart Can.27 lbs.

N.O.-4 Half Gallon Can ... 52 lbs.

The pads are made in three principal pat¬
terns: (1) Square, (2) Oblong (tapered), (3)
Pear shape. Straps are furnished various
lengths—two widths 1J4" and 1".

All leather used is first quality harness

leather. All sewing is lock stitched with
genuine linen thread hot waxed.

The buckles and buckle tongues are Klein
standard solid steel drop forgings—tested to
1500 lbs.

KLEIN'S CLIMBER STRAPS WITH SQUARE PADS

The set consists of:

2 upper (or calf) straps x 22".

2 lower (or ankle) straps 1J4" x 22".
2 square pads 4" x 4".

CAT. No.

5301-1 One *e+ complete with plain pads . .
5301-2 One set complete with sheep-lined pads
5301-3 One set complete with felt-lined pads .

WEIGHT PER DOZ. SETS

20 lbs.
20 lbs.
20 lbs.

SAME AS ABOVE BUT STRAPS I” WIDE.

5301-11 One set complete with plain pads. 18 lbs.

5301-12 One set complete with sheep-lined pads. 18 lbs.

5301-13 One set complete with felt-lined pads. 18 lbs.

KLEIN'S CLIMBER STRAPS WITH OBLONG PADS

"Bell System" Type

CAT. No.

5301-6 One set complete with plain pads . .
5301-7 One set complete with sheep-lined pads
5301-8 One set complete with felt-lined pads

The set consists of two upper or calf straps
1" x 22" with two special pads as shown and
two lower or ankle straps l" x 26".

WEIGHT PER DOZ. SETS

. 14 lbs.

. 15 lbs.

. 15 lbs.

These pads are made of select leather, arranged with loops for climber straps and climber.
Tapering 394" to 294" x 6/4" deep.

KLEIN'S "DEE" RINGS, SNAPS AND BUCKLES

Used on Body Belts, Safety Straps, Climber Straps, Etc.

All the above are solid steel forgings of ap- they should not be confused with ordinary
proved designs individually tested to 1500 commercial or harness fittings. All these
lbs. Each piece integral—no joints or welds. items are galvanized finish.

We make these fittings in our own shops—

"nPF /# We make three patterns of “Dee” Rings. All have 2)4 inch strap

Lsi-i- opening or clevis: (1) Standard—double bar, (2) Standard—single

bar, (3) “Hank’s”—single bar.

(1) (2) (3)

Standard—Double Bar Standard—Single Bar

♦“Hank's”

♦“Hank’s” Dee
Rings must be
used with corre-
s p o n d i n g
“Hank’s” Snaps
on Safety Strap.

QKI AP^ There are three patterns of snaps each with two sizes of clevis to fit strap
jINAr J widths 194 inch and 2 inch: (1) “Klein-Lok,” (2) Standard, (3) “Hank’s.”

O)

(U. S. Patent 1949608)

“Klein-Lok”

“Klein-Lok” Snaps provide an added
safety feature by an arrangement of twin
latches. The back latch locks the thumb
latch. To release from Dee Ring BOTH
latches must be depressed AT THE
SAME TIME. Operates quickly and
simply. Impossible to twist Dee Ring out
accidentally. Can be used with any Dee
Ring.

( 2 )

(3)

Standard

Wide nose covers
the latch to pre¬
vent “D” ring ac¬
cidentally releas¬
ing itself.

Once engaged it is impossible to re¬
lease the snap accidentally. Simple in
operation, positive in action. ("Hank’s”
Snaps must be used with corresponding
“Hank’s” “D” Rings on body belt.)

BUCKLES

W, 1 Va". 2".

Klein Buckles have drop forged frames and tongues. The frame is in one
piece—a real safety factor as compared with welded wire. Sizes: 1", 1J4"»
Types: (1) single tongue, (2) double tongue (194" and 2").

Double Tongue

KLEIN'S CLIMBER STRAPS

(Without Pads)

CAT. No.

5301- 4
5301- 9
5301-14
5301-10

One pair
One pair
One pair
One pair

2 straps)
2 straps)
2 straps)
2 straps)

|I/ 4 “x22”
I” x22”
|I/ 4 ”x26”
I" x26"

WEIGHT PER DOZ. PAIRS

.8 lbs.

.6 lbs.

.9 lbs.

.8 lbs.

KLEIN’S CLIMBER STRAPS (WITH PADS)

CAT. No. WEIGHT PER DOZ. PAIRS

5301- 5 One pair (2 straps). I I/ 4 "x22" with two plain pads 4 ,, x4”.12 lbs.

5301-15 One pair (2 straps). V' x22" with two plain pads 4"x4" .II lbs.

KLEIN'S SPECIAL ANKLE STRAPS

(For Ring Attachment on Klein No. 1939 Climbers)

CAT. No. WEIGHT PER DOZ. PAIRS

5301-16 One pair (2 straps) |l/|"x24". . 10 lbs.

5301-26 One pair (2 straps) I" x24".S 1 /* lbs.

Single Tongue

9

These special straps are made in two pieces
and are furnished with rivets and burrs.
Punched ready for quick attachment.

(We will rivet these ankle straps to No. 1939
climbers when so ordered.)

GENUINE KLEIN TOOLS

KLEIN'S CLIMBER PADS

(Standard Square Shape)

No. 8200

CAT. No. WEIGHT PER DOZ. PAIRS

8200 One pair (2 pcs.) Sheep-lined, 4"x4".4 lbs.

8201 One pair (2 pcs.) Felt-lined, 4"x4".4 lbs.

8202 One pair (2 pcs.) Plain leather, 4"x4".4 lbs.

Made of select harness leather with loops at back through which
climber strap passes.

KLEIN'S PEAR SHAPE CLIMBER PADS

No. 8206

CAT. No. WEIGHT PER DOZ. PAIRS

8206 One pair (2 pcs.) Plain leather, 3|/2"x6".4j/ 2 lbs.

These pads are made of two thicknesses of select harness leather
riveted together. The outer piece is punched with two slots for the
climber strap and one cross slot through which the leg iron of the
climber is passed. They are very comfortable, having all edges
round.

KLEIN'S "BELL SYSTEM" TYPE CLIMBER PADS

No. 8204

CAT. No.

8203 One pair (2 pcs.)

8204 One pair (2 pcs.)

8205 One pair (2 pcs.)

Plain leather
Sheep-lined .
Felt-lined

WEIGHT PER DOZ. PAIRS

.6 lbs.

.6 lbs.

KLEIN'S CLIMBER GAFF GUARDS

'5

No. 1929-G

CAT. No. WEIGHT PER DOZ. PAIRS

1929-G One pair (2 pcs.).I % lbs.

Made of harness leather. The “wings” of the guard fit around leg
iron of climber just above the gaff and snap on. The gaff is covered
and protected by the leather “fold over” as illustrated.

A simple safety item.

KLEIN'S LEATHER TOOL BELTS

Made in Sizes 36, 38, 40, 42, 44 and 46 Inches (Other sizes to order)

This belt is a new and somewhat novel pat¬
tern providing, in our opinion, the ultimate
in safety and comfort.

The cushion—4*4 inches wide at center of
back and tapered to 3 l / 2 inches wide at the

front—is made of one piece of soft, pliable,
yet tough, russet latigo leather, doubled to
form comfortable rolled edges and returned
at each end.

The body strap is first quality russet harness
leather 2 inches wide, stitched to the cushion
at back and passing through loops at end of
cushion as well as through the “dee” rings.
A russet harness leather tool strap 1inches
wide with five loops in the 1% inch loop
strap is carried on leather hangers from the
body strap to which it is looped at the ends.
This arrangement keeps the tool loops from
contracting when belt is buckled on and is
also another “comfort” feature.

So constructed that no rivets come through
to inside of belt—a safety insulation feature
that will be appreciated.

The “dee” rings are single bar type solid
steel drop forgings as is also the buckle.
All hardware tested to 1500 lbs. Galvanized
finish.

Fitted with leather plier pocket, knife snap
and tape thong complete.

WEIGHT PER DOZ

.... 45 lbs.
.... 45 lbs.

CAT. No.

5228 With Standard (Single bar) "D” Rings. Width 4l/ 2 in. (Complete)
H-5228 With "Hank's" 'D" Rings. Width 4>/ 2 in. (Complete).

KLEIN'S "TEXAS" BELT

No. 5204-TSO

CAT. No.

A popular belt made for comfort and safety.
The main belt is in one piece lined through¬
out with soft pliable latigo leather. Width
at center of back 4" tapered to 2*4" at hips.
Dee Rings and Buckle solid steel drop forg¬
ings tested to 1500 lbs. Galvanized finish.
No rivets go through belt—a special insulat¬
ing feature.

All rivets are solid copper hand set with
burrs. Sewing is with hot waxed linen
thread, lock stitched.

Has latigo flap to which plier pocket may be
riveted.

WEIGHT PER DOZ.

36 lbs.
36 lbs.

5204-T.S.O. With Standard ”D" Rings (single bar). Width 4 in.
H-5204-T.S.O. With "Hank’s" "D" Rings. Width 4 in. . . .

GENUINE KLEIN TOOL BELTS

Drop Forged Tested Hardware

KLEIN'S LEATHER TOOL BELTS

Made in Sizes 36, 38, 40, 42, 44 and 46 Inches (Other sizes to order)

DIRECTIONS TO ENSURE PROPER FIT OF LINEMEN'S BELTS

Linemen's belts are usually specified by waist
or body size but to ensure comfort in use it
is important that the “D” rings do not rest
on the hip-bones of the wearer. The correct
position of the “D” rings is about 1 inch in
front of the hip-bone on either side.

To obtain correct body size of Klein’s Tool
Belt, measure (around the back) from hip¬
bone to hip-bone AND ADD TWO INCHES
to this distance.

Then refer to table below and select the cor¬
responding belt size.

Distance between
“D” Rings.

20 in.

22 in.

22 in.

24 in.

26 in.

28 in.

Belt Size.

36 in.

38 in.

40 in.

42 in.

44 in.

46 in.

You may order by size or by distance between "D” rings.

"Hank's" Snaps and "D" Rings

U. S. Patent, No. 1755286

msvrr .—"

The special construction of “Hank’s” Snaps
and “D” Rings is such that once engaged, it
is impossible to release the snap accidentally
from the “D” ring. Yet, when desired, by
entirely reversing the snap from the normal

position and giving a quick push forward
the operation is accomplished in a second.
No thumbing of spring latch is necessary—a
boon to the lineman in cold weather or when
wearing gloves.

The nose of the snap is returned so that it
forms almost a complete “U” with the shank
of the hook and by keeping the safety latch
inside this nose, the latch is protected from
accidental opening as may be caused in the
ordinary snap by pressing against a cross
arm brace or similar object with which it
may come in contact.

The “D” ring is forged in a wedge cross
section with the thin edge inwards.

The snap is engaged with the “D” in the
regular way but IN RELEASING, THE
SNAP MUST BE ENTIRELY REVERSED
TO ITS NATURAL POSITION and a
quick push given to drive the wedge of the
“D” into a narrow entrance provided in the
snap between the latch and the nose.
Refe-ence to the illustration will make the
operation easily understood.

Note:—"Hank’s" Belts and Safety Straps MUST be used together. They cannot be used in connection with
other fittings.

First quality and selection harness leather
throughout. The cushion, 3*4 inches wide,
carries the Dee rings. The outer strap or
tool loop is 1 y 2 inches wide, formed into
loops by riveting to the cushion. As an addi¬
tional safety factor it is also passed through
the Dee rings. Dee rings and buckle are solid
steel drop forgings of improved design,
everyone tested to 1500 lbs. Surfaces taking
the wear of the Dee rings are protected by
copper safety liners riveted through the full
thickness of the belt. A leather pocket is
provided for pliers, also a convenient snap
for carrying knife. At the other end of the
belt a rawhide thong is attached with fibre
cross bar for carrying tape. All rivets are
solid copper, hand set with burrs. Sewing is
with linen thread, hot waxed and lock
stitched. A safety belt that is safe. The wide
cushion makes it preferred by some for the
comfort it gives in use. “D” rings and buckle
galvanized finish.

CAT. No.

5204-D.E. With Standard "D" Rings. Width 3>/ 2 in.
H-5204-D.E. With "Hank's" "D" Rings. Width 3'/ 2 in.

WEIGHT PER DOZ.

. ... 38 lbs.
. ... 38 lbs.

Made of select first quality harness leather.
The cushion 3 l / 2 inches wide carries the “D”
rings. The outer or loop layer is V/ 2 inches
wide formed into tool loops by riveting to
the cushion. It also passes through the “D"
rings and is furnished with a strong drop
forged buckle tested to 1500 lbs.

The “D” rings are solid steel drop forgings
tested to 1500 lbs. Surfaces taking the wear
of the “D” rings are protected with copper
safety liners riveted through the full thick¬
ness of belt. All rivets are solid copper set
with burrs and sewing is with hot waxed
linen thread, lock stitched. “D" rings and
buckle galvanized finish.

CAT. No . WEIGHT PER DOZ.

5204 With Standard ”D" Rings (double bar). Width 3!/ 2 ".34 lbs.

H-5204 With "Hank’s" "D" Rings. Width 3'/ 2 ’.34 lbs.

No. 5204

10

GENUINE KLEIN TOOLS

KLEIN'S LEATHER TOOL BELTS

Made in Sizes 36, 38, 40, 42, 44 and 46 Inches (Other sizes to order)

No. 5205

Made of select first quality harness leather.
The inner or cushion layer 2}4 inches wide
carries the “D” rings and is locked stitched
and riveted to the outer layer which also
passes through the “D” rings and is fur¬
nished with a strong drop forged buckle
tested to 1500 lbs. Galvanized finish.

The “D” rings are solid steel drop forgings
tested to 1500 lbs. Surfaces which take the
wear of the “D” rings are protected with
copper safety liners riveted to the belt. “D”
rings and buckle are galvanized finish. All
rivets are solid copper, set with burrs and
sewing is with hot waxed linen thread, lock
stitched. The loop strap is 1% inches wide
formed into 6 loops.

CAT. No. WEIGHT PER DOZ.

5205 With Standard "D" Ring* (double bar). Width 2(4" (double thickness).35 lbs.

H-5205 With "Hank's" "D" Rings. Width 2'/ 4 " (double thickness).35 lbs.

No. 5202

Made of select first quality harness leather.
The cushion 2*4 inches wide carries the “D"
rings. The outer or loop layer is 1 y 2 inches
wide formed into tool loops by riveting to
the cushion. It also passes through the “D”
rings and is furnished with a strong drop
forged buckle tested to 1500 lbs.

The “D” rings are solid steel drop forgings
of improved design, tested to 1500 lbs. Sur¬
faces taking the wear of the “D” rings are
protected with copper safety liners riveted
through the full thickness of belt. All rivets
are solid copper set with burrs and sewing is
with hot waxed linen thread, lock stitched.
“D” rings and buckle galvanized finish.

CAT. No. WEIGHT PER DOZ.

5202 Wirt Standard "D" Rings (double bar) Width 2l/ 4 ".32 lbs.

H-5202 With "Hank's" "D" Rings Width 2'/ 4 ".32 lbs.

KLEIN'S DERRICK BELT

Made in One Size—Adjustable from 36" to 44"

No. 5212

This belt is designed for maximum safety for
use by derrickmen, structural steel workers,

CAT. No.

5212 3 in. wide. I "Dee" Ring.

tree surgeons, tower erectors, etc. The main
belt is one piece of first quality harness
leather three inches wide at the back, tapered
to two inches in width at the buckle. A three
inch forged steel dee ring is set at center of
back to provide means for securely anchoring
the life line or rope. The buckle is solid
forged frame fitted with double tongues to
guard against slitting the belt in event of a
fall. Designed to stand a load of 250 lbs. on
a dead fall of five feet. Adjustable for sizes
36" to 44".

WEIGHT PER DOZ.

.30 lbs.

KLEIN'S STEEL WORKER'S BELT

Made in One Size—Adjustable from 36" to 44"

No. 5214

Steel Worker’s Belt made of one piece of
first quality harness leather two inches wide

and fitted with three forged dee rings for
attachment of life line in most convenient
position. A leather loop is provided for
wrench.

The main belt passes through the dee rings
which are held in place by backing pieces of
latigo leather stitched and riveted to the belt
proper.

The two inch buckle is of the double tongue
type with solid forged frame.

Distance between outer dee rings 24". Ad¬
justable for sizes 36" to 44".

CAT. No.

5214 2 in. wide. 3 "Dee” Rings.

5214-0 Same as above but without wrench loop

WEIGHT PER DOZ.

. . . . 28 lbs.

27l/ 2 lbs.

KLEIN'S LEATHER BELT AND SAFETY STRAP

Drop Forged Tested Hardware

The Tool Belt in this outfit is same as No. 5202. The safety strap is
the No. 5250. Belt 2*4 inches wide. Strap 1^4 inches. All snaps, “D"
rings and buckles are solid steel drop forgings tested to 1500 lbs. and
are galvanized finsh. The strap may be adjusted to any length by
means of buckle or it may be detached entirely from belt.

First quality harness leather throughout. Hot waxed linen thread,
lock stitched. A very popular combination—thoroughly dependable.
CAT. No. SIZE WEIGHT PER DOZ.

5206-1A Strap I % in. x 5 ft. 8 in.62 lbs.

Belt (as ordered) 36, 38, 40, 42, 44 and 46 in.

KLEIN'S LEATHER TOOL BELTS

KLEIN'S LEATHER SAFETY HARNESS

Made in Sizes 36, 38, 40, 42, 44 and 46 Inches (Other sizes to order)

First quality harness leather throughout.
The inner or cushion layer, 3 inches wide, is
narrowed at each end to carry the “D” rings.
The body strap, 2 inches wide, is riveted and
stitched to the cushion and also passes
through the “D” rings. Two tool straps are
provided and formed into two loops at each
side of the belt by riveting through the two
layers of belt proper. "D” rings and buckle
are solid steel drop forgings of improved
design, each tested to 1500 lbs. They are
made in our own shops and are galvanized to
prevent rust. Surfaces taking the wear of the
"D” rings are protected by copper safety
liners riveted through the full thickness of

No. 5211

the belt. All rivets are solid copper, hand set
with burrs. Sewing is with linen thread, hot
waxed and lock stitched.

WEIGHT PER DOZ.

.... 34 lbs.
.... 34 lbs.

CAT. No.

5211 With Standard "D" Rings (double bar) Width 3'
H-52II With "Hank's" "D" Rings Width 3".

an CAT. No. WEIGHT PER DOZ.

5209 Harness complete with life line. % in. rope, 25 ft. long 75 lbs.

This harness has been de¬
signed for use where danger
from gassing is present.

Working in gassy manholes,
gas tanks, oil tanks and even
boilers, men are frequently
overcome and an emergency
arises instantly. This harness
provides a sure means by
which the patient can be
brought to safety, and the
danger overcome. The design
of the harness is such that it
slings the wearer in a perpen¬
dicular position so that he can
be readily hauled through
ordinary manhole opening.

A solid harness leather back
plate 2J4 inches by 10 inches is stitched and
riveted around the 1J4 inch adjustable belt
strap. The back plate also carries a tested
drop forged “D” ring to which the ^4 inch
manila life line, 25 feet in length, is perma¬
nently attached.

The shoulder straps are ?4 inch and made ad¬
justable and riveted to the belt at the single
ends.

These straps serve to hold the belt in posi¬
tion around the chest, so as not to encumber
the wearer while working.

KLEIN'S COMBINATION LEATHER AND
"KLEIN-KORD" BELT

Made in Sizes 36, 38, 40, 42, 44 and 46 Inches (Other sizes to order)

Built of a combination of harness leather
and “Klein-Kord” fabric (see page 54).

The leather cushion is 3 inches wide tapered
at the hips. To it is stitched the top (or
body) strap of 1^4 inch x 6 ply “Klein-Kord.”
A leather strap 1 inch wide is riveted to the
body strap to form five tool loops of conven¬
ient size. Fitted complete with leather plier
pocket, knife snap and tape-thong.

This construction makes an exceedingly
strong belt and one that will not stretch be¬
tween the “Dee” rings. Rings and Buckle
are solid steel drop forgings individually
tested to 1500 lbs. Galvanized finish.

CAT. No. WEIGHT PER DOZ

5221-KK With Standard (Single bar) "Dee" Rings. Width 3 in.36 lbs.

H-522I-KK With "Hank's" "Dee" Rings. Width 3 in.. 36 lbs.

KLEIN'S FABRIC TOOL BELT

Made in Sizes 36, 38, 40, 42, 44 and 46 Inches

This belt is constructed throughout of a new
rubberized fabric specially designed to pro¬
vide the full factor of safety required.

The fabric is made up of a number of plies
laid and vulcanized in live rubber in such a
way as to secure the flexibility necessary for
comfort as well as to protect the fabric from
the weather. The inner surfaces are left un¬
treated to prevent condensation from body
heat which might otherwise occur.

The cushion is 3 inches wide tapered at the
hips where it is returned through the double
bar “dee” rings. The body, or top strap, is
1*4 inches wide riveted to the cushion to
form four tool loops of convenient size. It
also passes through the “dees” as an addi¬
tional safety precaution. All edges are lock
stitched with genuine linen thread. “Dee”
Rings and Buckle are solid steel drop forg-

CAT. No.

5227-KK With Standard "D" Rings. Width 3 in.
H-5227-KK With "Hank's" "D" Rings. Width 3 in.

No. 5227-KK

ings, individually tested to 1500 lbs. Galvan¬
ized finish.

Line Patrolmen, Inspectors, Service men and
others who must carry a belt for occasional
use will find this one particularly convenient
on account of its light weight and ability to
pack into very small space.

(We are in a position to make to order varia¬
tions of the design shown and will be pleased
to quote on special requirements.)

WEIGHT PER DOZ.

.25 lbs.

.25 lbs.

11

GENUINE KLEIN TOOLS

KLEIN'S LEATHER SAFETY STRAPS-1 ft" WIDE

Drop Forged Tested Hardware

These straps are cut from first quality harness leather, back or center stock only. All rivets
solid copper, hand set with burrs. Snaps and buckles solid steel drop forgings tested to 1500
lbs., galvanized finish. Straps may be lengthened or shortened by adjusting buckle.

No. 5251

CAT. No. SIZE AND DESCRIPTION WEIGHT PER DOZ.

KL-5251 I % in. X 5 ft. 8 in. "Klein-Lolc" Snaps. Leather wear pad at buckle.32l/j lbs.

5251 I ft in. x 5 ft. 8 in. Standard Snaps. Leather wear pad at buckle.32l/ 2 lbs.

H-5251 1% in. x 5 ft. 8 in. "Hank's" Snaps. Leather wear pad at buckle.32'/ 2 lbs.

(This series supersedes Nos. KL-5251-T, 5251-T and H-5251-T)

CAT. No. SIZE AND DESCRIPTION WEIGHT PER DOZ.

KL-5250 I ft in. x 5 ft. 8 in. "Klein-Lok" Snaps. Stainless Clips.321/j lbs.

5250 1% in. x 5 ft. 8 in. Standard Snaps. Stainless Clips.32>/ 2 lbs.

H -5250 I ft in. x 5 ft. 8 in. "Hank’s" Snaps. Stainless Clips.32*/j lbs.

KLEIN'S LEATHER EXTENSION STRAPS

No. 5215

CAT. No. SIZE

5215 I ft in. X 15 in. Forged "D" Ring .
H-5215 I ft in. x 15 in. "Hank's" "D" Ring

l5*/ 2 lbs.
17 lbs.

These extension straps are worn permanent- makes it necessary to “extend" the regular
ly attached to one “D” ring on body belt. safety strap.

They are brought into use when a large pole

KLEIN-KORD

The RED CENTER Fabric
For Linemen’s Safety Straps

U 2?*2'M« "STOP WHEN YOU SEE RED"

“Klein-Kord” Safety Straps are standard equip¬
ment with leading Public Utility Companies, Tele¬
phone Companies and others desiring the maximum
of safety for their men.

"Klein-Kord” Red Center provides for the first
time something Safety Engineers have sought for
years—a definite warning when to discard a safety
strap.

“Klein-Kord" Red Center fabric is made of six
plies of long staple cotton of special weave, each
ply laid in rubber and vulcanized. This construc¬
tion provides maximum strength and safety.

Red rubber is used on the two center plies to pro¬
vide an unmistakable signal when the use of the
strap should be discontinued.

The “Klein-Kord” Red Center Safety Strap may be
used with perfect safety until two outside plies
are worn completely through. Then (it speaks for
itself)

"STOP WHEN YOU SEE RED"

At this point there still remains an ample factor of
safety—but it is good judgment to take the strap
out of service.

“Klein-Kord” must not be confused with rubber
transmission belting. In “Klein-Kord” the cross
cords are extra strength so as to permit the use of
the tongue type of buckle without risk of slitting
or ripping under severe tension. (A friction buckle
is unsuitable on a safety strap because the possi¬
bility of slip makes it decidedly objectionable.)
When tested as in use a “Klein-Kord” Safety Strap
will take a load of 2400 lbs. before ripping takes
place at the tongue, which compares favorably with
a high quality leather safety strap where ripping
would probably occur at about 1750 lbs. The ten¬
sile strength per square inch of “Klein-Kord" is
5660 lbs. as against the usual specifications for first
quality harness leather of 3500 lbs. In order to
overcome any tendency to stretch, a leather strap
2 inches wide is frequently used. With “Klein-
Kord” there is no appreciable permanent stretch,
and we have found that a width of 1 y 4 inches pro¬
vides a full factor of safety. For extra long wear
all “Klein-Kord” safety straps are fitted with stain¬
less steel reinforcements at buckle and fixed snap.
We unhesitatingly recommend “Klein-Kord” Safety
Straps to our many friends.

ADVANTAGES

1. Guess work as to safe period of use eliminated.

2. Great tensile strength. Factor of safety—plus

3. Weatherproof.

4. Extremely tough; resists damage from acci¬
dental cuts, heat, etc.

5. Uniformity of thickness and strength.

6. Safety Straps can be made any length required.

7. Low conductivity. Flexible.

8. Permits use of regular tongue buckle for posi¬
tive length adjustment.

9. No stretch in use.

10. Can be used for all purposes. On poles, towers
or tree trimming work.

CARE OF "KLEIN-KORD"

The life of “Klein-Kord” will be materially in¬
creased by dressing at intervals with "Klein-Kord”
dressing. The first dressing should be applied as
soon as the original rubber finish is worn from the
surfaces—the fabric is then exposed so that it will
absorb the dressing. Brush in a liberal first coat
and allow to soak in and dry at room temperature
for about an hour. Then apply a lighter second
coat and do not use strap until thoroughly dry.
This treatment will protect the fabric and provide
a “slick” surface which in use will slide over the
pole freely.

CAUTION

Use special dressing only. Ordinary varnishes or
lacquers are not satisfactory and may ruin your
strap.

For the convenience of our customers we furnish
“Klein-Kord” dressing in y 4 pint cans, with full
directions for use as follows:

"KLEIN-KORD" DRESSING

CAT. No. WEIGHT PER DOZ.

K.K.D.-025 l/ 4 pinf con.4 lbs. 11 ox.

KLEIN'S LEATHER SAFETY STRAPS-2” WIDE KLEIN’S "KLEIN-KORD" SAFETY STRAPS -RED CENTER

These straps are cut from
first quality harness leather,
back or center stock only. All
rivets solid copper set with
burrs. Drop forged roller
snaps and buckles tested in¬
dividually to 1500 pounds,
galvanized finish. Straps may
be lengthened or shortened by adjusting

buckle. Reinforced both ends with stainless

steel safety clips riveted through double
thickness of the leather.

CAT. No. SIZE AND DESCRIPTION

KL-5253 2 in. x 5 ft. 8 in. "Klein-Lok" Snaps. Stainless Clips

5253 2 in. x 5 ft. 8 in. Standard Snaps. Stainless Clips

H -5253 2 in. x 5 ft. 8 in. "Hank’s" Snaps. Stainless Clips

WEIGHT PER DOZ.

40 lbs.
40 lbs.
40 lbs.

The 5253 series can be furnished to order with leather wear pad at buckle instead of stainless steel clip.
Order as KL-52S3-T. S253-T or H-5253-T.

This strap is similar to the
No. 5253 but has a double
tongue buckle. First quality
and selection harness leather
cut strictly from center or
back stock only. Securely
sewed with linen thread, hot
waxed, lock stitched. Solid
copper rivets and burrs set by hand. Snaps
and buckle are solid steel drop forgings
individually tested to 1500 lbs. They are
made in our own shops and are galvanized
to prevent rust. The strap may be length-

CAT. No. SIZE AND DESCRIPTION

5257-S 2 in. x 5 ft. M/ 2
5257-L 2 in. x 5 ft. 10 in.

ened or shortened by adjusting buckle. One
end reinforced with stainless steel safety
clip. The single end is returned through
roller of snap and securely sewed and
riveted.

WEIGHT PER DOZ.

39 lbs.
41 lbs.

in. "Bell System" type. Drop Forged Roller Snaps
Bell System" type. Drop Forged Roller Snaps

CAT. No. SIZE AND DESCRIPTION

KL-5233 I ft in. x 5 ft. 8 in. "Klein-Lok" Snaps. Stainless Clips

To avoid substitutes see that
every strap has our registered
trade name, "KLEIN-KORD,”
molded into the surface.

WEIGHT PER DOZ.

. . . . 36 lbs.

(Other lengths can be furnished to order.)

CAT. No. SIZE AND DESCRIPTION WEIGHT PER DOZ.

5233 I ft in. x 5 ft. 8 in. Standard Snaps. Stainless Clips.36 lbs.

(Other lengths can be furnished to order.)

CAT. No. SIZE AND DESCRIPTION WEIGHT PER DOZ.

H-5233 I ft in. x 5 ft. 8 in. "Hank's" Snaps. Stainless Clips.36 lbs.

(Other lengths can be furnished to order.) *

(“Hank’s” Snaps must be used with corresponding “Hank's” “D” Rings on body belt.)

KLEIN'S "KLEIN-KORD" SAFETY STRAPS

(Fixed Length Type)

This strap is a heavy duty
type following the N.E.L.A.
specifications. First quality
and selection harness leather
throughout, cut from center
or back stock only. Sewing is
with linen thread, hot waxed,
lock stitched. Solid copper
rivets with burrs hand set.

Snaps and buckle are solid steel drop forg¬
ings tested to 1500 lbs. They are made in
our own shops and galvanized to prevent
rust. The strap may be lengthened or short-

CAT No. SIZE AND DESCRIPTION

KL-5258 2 in. x 5 ft. 6 in. "Klein-Lok” Snaps.

5258 2 in. x 5 ft. 6 in. Standard Snaps.

H -5258 2 in. x 5 ft. 6 in. "Hank’s" Snaps.

ened by adjusting the buckle. Reinforced at
buckle end with stainless steel safety clip,
at the fixed snap the strap is returned and
secured by sewing and riveting.

WEIGHT PER DOZ.

40 lbs.
40 lbs.
40 lbs.

On properties where there is no great varia¬
tion of pole sizes the uniform strength of
“Klein-Kord” fabric often makes it possible

to adopt a safety strap of
fixed length. With conven¬
tional straps the greatest wear
is usually close to the buckle.
The fixed length strap avoids
this due to the smooth way it
moves on the pole.

We can furnish the above types of safety
straps in any desired length to order.

CAT. No. SIZE AND DESCRIPTION WEIGHT PER DOZ.

KL-5234 I ft in x 56 in. (effective length) with "Klein-Lok" Snaps.25*/ 2 lbs.

5234 I ft in. x 56 in. (effective length) with Standard Snaps.25>/ 2 lbs.

H -5234 I ft in. x 56 in. (effective length) with "Hank's" Snaps.25 l / 2 lbs.

Stainless Clip
Stainless Clip
Stainless Clip

12

GENUINE KLEIN TOOLS

KLEIN'S "KLEIN-KORD" EXTENSION STRAPS

No. 5236

CAT. No. SIZE AND DESCRIPTION

KL-5236 1% in. x 15 in. with Standard "D” and "Klein-Lok" Snap

5236 1% in. x 15 in. with Standard "D" and Standard Snap .

H -5236 1% in. x 15 in. with "Hank's" "D" and "Hank's" Snap .

WEIGHT PER DOZ.

The Extension Strap is used in conjunction
with a fixed length Safety Strap. It provides
the extra length necessary when working on

large diameter poles. May be worn on belt
ready for immediate use or carried in truck.

KLEIN'S BELT ACCESSORIES

HIP POCKET TOOL CASE DETACHABLE HOLSTER

CAT. No. SIZE WEIGHT PER DOZ.

5111 Sin. X 7 in.S'/a lbs.

For carrying pliers or other tools in hip
pocket. Prevents cutting of clothes, or pos¬
sible injury to the person. Made of black
leather.

CAT. No. SIZE

5116 10 in. long

WEIGHT PER DOZ-

. . . . 6 lbs.

Made of heavy harness leather with loop to
slip over belt. Carries 6, 7, 8. or 9 inch side
cutting pliers. Mouth of pocket framed to
hold open position permanently.

Tape-Thong

No. 5130

Knife Snap

No. 5131

CAT. No. DESCRIPTION

5130 Tape-thong with fiber cross bar

5131 Knife Snap with strap and rivets

5132 Ring with strap and rivets . .

Ring

No. 5132

WEIGHT PER DOZ

.... fj lb.

. . . . l'/ 2 lbs.

.... ■/, lb.

The Tape-thong illustrated above provides a
convenient arrangement for carrying a roll
of tape. The thong is pliable latigo leather
10 inches long x fg inches wide, slit to form
loops at both ends. One end is looped to a

fiber cross bar V/i inches long. The other
loop may be attached readily to the belt.
The Knife Snap and ring are both mounted
on harness leather straps and come with
rivets and burrs ready for attaching to belt.

PLIER POCKETS

CAT No. SIZE WEIGHT PER DOZ.

5107 31/j in. X 8l/ 2 in.3 lbs.

Made of a good quality leather. For carrying 6. 7, 8, or
9 inch pliers when at work. Has slits through which
belt may be inserted or can be riveted on.

CAT. No. SIZE WEIGHT PER DOZ.

5112 3*/ 2 in. x 9 in.4% lbs.

Similar to No. 5107 except plier does not protrude. Bot¬
tom is left open to prevent collection of dirt, etc. A
loop is riveted at back through which belt may be
passed or can be riveted on.

No. 5112

POUCH FOR RUBBER GLOVES

CAT. No. SIZE

5120-9 7*/ 2 in. x 9 in. deep

WEIGHT PER DOZ

... 4l/ 2 lbs.

Scotch chrome leather pocket for carrying rubber gloves (folded). Comes
equipped with snap and “D” ring, ready to attach to body belt.

CAT. No. size

5120-15 7'/j in. x 15 in. deep

WEIGHT PER DOZ.

.... 7 lbs.

Same as above but larger to accommodate gloves without folding.

KLEIN'S CANVAS "TOOL-PACK"

No. 5139

Every mechanic will recognize the advantages of the “Tool
Pack.” It is a sturdy, brown, canvas bag, approximately 6"
x 12". A heavy zipper instantly opens or closes the full
length mouth. Just the thing to keep a selection of fre¬
quently used small tools separated where they can be found
at once—no “digging” around in the big bag. Plenty of
room for pliers, small screwdriver, drill, wrenches, etc.
You’ll wonder how you got along without it.

CAT. No. SIZE WEIGHT PER DOZ.

5139 6 in. x 12 in..3 lbs.

KNIFE POCKET

CAT. No. SIZE WEIGHT PER DOZ.

5163 3“x9".4 lbs -

This harness leather pouch is made specially for the No. 1560-3 Skinning
Knife. It can be carried in the hip pocket or riveted to belt as preferred.
Lock stitched with genuine hot waxed linen thread. An opening at bottom
of the pouch prevents accumulation of water or dirt. This pouch provides
a safe method for carrying a useful knife.

COMBINATION TOOL POCKETS

CAT. No. SIZE AND DESCRIPTION

5II8-K 4%"x8" For Plier and Knife.

5II8-S 4“ x8" For Plier and Screwdriver . . .
5II8-R 4%"x8" For Plier and 6 ff. Rule . . . .

These pockets are made of heavy harness
leather. Opening at bottom prevents accu¬
mulation of dirt or water. Top flap of double

WEIGHT PER DOZ.

.71/, lbs.

.B^lbs.

.7t/j lbs.

thickness leather for riveting to belt. (The
plier compartment fits 6, 7, 8, and 9 inch side
cutting plier.)

INSPECTOR'S HARNESS LEATHER TOOL BAG

CAT. No.

No. 5108

WEIGHT EACH

5108-14

14x8 inches ....

. . . 5 lbs.

5108-16

16x8 inches ....

. . . 5% lbs.

5108-18

18x8 inches ....

5108-20

20x8 inches ....

5108-22

22x8 inches ....

... 7 lbs.

5108-24

24x8 inches ....

. . . 71/4 lbs.

This bag offers a combination of good fea¬
tures. It is made of harness leather and will
stand rough and hard usage and still always
look well. It has a shoulder strap combined
with a pad and hand strap. The bottom is
three ply and is protected with steel studs.
Retaining straps pass clear around the bag
so that it may be loaded to the limit of its
capacity and be securely held intact. All
seams are sewed with hot waxed linen thread,
lock stitched. The leather used does not ab¬
sorb moisture.

LINEMEN'S CANVAS TOOL BAG, LEATHER BOTTOM

These bags are made of one piece of white
duck reinforced all around the bottom with
heavy bag leather, VA inches up on the 5102
series, 8 inches up on the 5105 series. The
bottom is made of heavy leather outside and
duck inside, lock stitched all around. The
bottom is protected with strong steel studs.

No. 5102

CAT. No.

SIZE

WEIGHT EACH

5102-12

12-inch . . .

. 2 Va

lbs.

5102-14

14-inch . . .

.2'/a

lbs.

5102-16

16-inch . . .

.3

lbs.

5102-18

18-inch . . .

.3'/ 4

lbs.

5102-20

20-inch . . .

.3/2

lbs.

5102-22

22-inch . . .

.3y 4

lbs.

5102-24

24-inch . . .

.4

lbs.

Bottoms and sides are joined together with
lock stitched leather welt seams. Mouth of
the bag is formed by a 12-gauge steel frame;
the canvas is clinched between this frame
and an inside secondary steel frame. Has
harness leather handles and two retaining
straps with buckles.

No. 5105

CAT. No SIZE

5105-16 16-inch .

5105-18 18-inch .

5105-20 20-inch .

5105-22 22-inch .

5105-24 24-inch .

WEIGHT EACH

lbs.
lbs.
lbs.
lbs.
41/4 lbs.

%

The above bags can be furnished with lock and key, also shoulder strap to order at slight additional cost.

13

GENUINE KLEIN TOOLS

KLEIN'S "CHICAGO" GRIPS

Construction engineers are more and more
demanding grips which will neither slip nor
damage the conductor or strand under heavy
loads. These requirements have been met by
welding a lining of bronze into the jaws of
standard “Chicago” Grips.

To insure maximum efficiency and avoid
slippage, keep the grooves of jaws of “Chi¬
cago” Grips free of grease, oil, accumulation
of spelter, etc. (Use emery paper or fine cut
file if necessary.)

Main body piece and lever are forged steel.
Draw parts are of wrought steel. Gripping
jaws are machined smooth. Rivets are ma¬
chine turned and workmanship throughout
is first class.

To Decide on Size Grip Required
Consult reference tables in the back of this
catalog giving diameters of solid wires and
also copper and aluminum strands in general

use. For your convenience there is also a
table giving decimal equivalents of fractions.
(Page 84.)

If you cannot decide on grip for your pur¬
pose send us full particulars with outside
diameter of wire or strand and we will ad¬
vise promptly.

Once these grips seize the wire they hold on
with the tenacity of a bull dog. The harder
the pull, the tighter the hold. Pulls straight
without leaving kinks in the wire. Handy
to put on and holds in place by means of
a spring acting on the compressing lever.
A noteworthy feature is the arrangement of
the draw link so that it does not hang down
at right angles, and is therefore not in the
way of the line when the grip is put on.

In the following listings Grips with bronze lined jaws
are indicated by the letter "B” after the catalog
number. (Thus I628-5B.)

CAT. No.

I628-5B

1628-5

KLEIN'S IMPROVED "CHICAGO" GRIP

THE "ALL PURPOSE" TOOL

For Messenger, Guy Strand and Conductors up to 1/2 in. Diameter

No. 1628-5-B

With bronze lined jaws

No. 4 B.&S. Solid Copper (.202")
No. 6 A.C.S.R. (.198")

MAX. SAFE WEIGHT

OPENING LOAD EACH

.58 in. 8,000 lbs. 6 lbs.

As above but without bronze lining in jaws.

The above grip has been designed to pro¬
vide in one tool a grip to handle almost
every requirement on the usual job.

The jaws have been lengthened and the
leverage increased. No. 1628-5B has bronze-
lined jaws to prevent slippage and conse¬

quent damage to galvanized finish or to
copper or aluminum conductors.

For “all purposes” on any strand or solid
wire up to 54 inch diameter with load up to
8000 lbs. Weighs only 6 lbs.

Forged from Alloy Steel—heat treated.

KLEIN'S "CHICAGO" GRIPS FOR
STRANDED CONDUCTORS

The 1626 series is similar to the 1613 series
construction but the necessary extra width
in the jaws is “lipped” out to avoid unneces¬
sary weight. Both gripping jaws are smooth.

NOTE: Grips for other size Cables made to order.

CAT. No. CABLE SIZE CABLE SIZE OPENING LOAD

1626-39 300.000 C.M. A.C.S.R. (.680") 3/0 A.C.S.R. (.502") .75 in. 3,750 lbs.

350,000 C.M. Copper (.679") 4/0 Copper Strand (.522")

*I626-39B As above but bronze lined jaws.

1626-40 500,000 C.M. A.C.S.R. (.904") 4/0 A.C.S.R. (.563") .97 in. 3,750 lbs.

600,000 C.M. Copper (.891") 250,000 C.M. Copper (.575")

*I626-40B As above but bronze lined jaws.

*I626-AB Furnished to order. Forged from Alloy Steel—Heat Treated Bronze-lined jaws.

300,000 C.M. A.C.S.R. (.680") 3/0 A.C.S.R. (.502") .75 in. 8,000 lbs.

350.000 C.M. Copper (.679") 4/0 Copper Strand (.522")

7 I /2 lbs.
71/2 lbs.

71/2 lbs.

•Bronz# lining of jaws prevents slippage and consequent surface abrasion of cable.

KLEIN'S "CHICAGO" GRIPS FOR BARE WIRES

(Solid and Strand)

The 1613 series is constructed as above de-
scribed with the plain type of jaw as suited
for bare wire.

1613-30 No. 6 B. & S. Solid (. 162") No. 12 B. & S. Solid (.081") .22 in.

I6I3-30B As above but bronze lined jaws.

1613-40 No. 0 B. & S. Strand (.373") No. 10 B. & S. Solid (. 102") .44 in.

I6I3-40B As above but bronze lined jaws.

(1613-40, 1613-40B supersede previous Nos. 1613-40A and 1613-40AB.)

1613-50 No. 4/0 B. & S. Solid (.460") No. 6 B. & S. Solid (. 162") .52 in.

I6I3-50B As above but bronze lined jaws.

1613-50A No. 4/0 B. & S. Strand (.552") No. 6 B. & S. Solid (. 162") .62 in.

I6I3-50AB As above but bronze lined jaws.

Bronze lining of jaws prevents slippage and consequent surface abrasion of conductor or strand.

LOAD

WEIGHT

EACH

SIZE

No.

1,500 lbs.

11/ 2 lbs.

1

2,250 lbs.

3 lbs.

2

4,000 lbs.

8 lbs.

3

4,000 lbs.

8 lbs.

3A

KLEIN'S "CHICAGO" GRIPS FOR INSULATED WIRE

With "Saw Tooth" Upper Jaw

CAT. No WIRE SIZE

1611-20 No. 4 B. a S. Weatherproof
Solid (.391")

1611-30 No. I B AS. Weatherproof
Solid (.500")

1611-40 No. 2/0 B. & S. Weatherproof
Strand (.672")

1611-50 No. 4/0 B. a S. Weatherproof
Strand (.860"|

(Supersedes 1611-ST series.)

No. 10 8. a S. Weatherproof
Solid (.250")

No. 6 B. a S. Weatherproof
Solid (.313")

No. I B. a S. Weatherproof
Solid (.500")

No. 2/0 B. a S. Weatherproof
Strand (.672")

APPROX.

MAX SAFE WEIGHT SIZE

OPENING LOAD EACH No.

.50 in.

2,200 lbs.

3 lbs.

6

.56 in.

3,500 lbs.

3% lbs.

4

.75 in.

3,750 lbs.

7% lbs.

5

.94 in.

3,750 lbs.

7% lbs.

5A

The 1611 series is similar to the 1613 series unnecessary weight. The upper jaw has

in construction but the necessary extra “saw-tooth" gripping notches,

width in the jaws is “lipped” out to avoid

The 1611 Series of Grips can be furnished with bronze lined jaws to special order. (Order as I6II-20B,
161 I-30B, etc.)

KLEIN'S "CHICAGO" GRIPS FOR MESSENGER AND
GUY STRAND, HEAVY CABLES, WIRE ROPE, ETC.

CAT. No.

1628-6

I628-6B

1628-16

MAXIMUM MINIMUM

CABLE SIZE CABLE SIZE <

7/16" Galvanized Steel Strand (.438”) 3/16" Galvanized Steel Sfrd. (.188")

No. 2/0 B. a S. Copper Strd. (.414") No. 5 B. a S. Copper Solid (.182")

No. 1/0 A.C.S.R. (.398") No. 7 A.C.S.R. (.177")

8,000 lbs. 8 1/2 lbs.

As above but bronze lined jaws for stranded conductors.

ft" Galvanized Steel Strand (.625") 5/16" Galvanized Steel Strd. (.312") .69 in. 15,000 lbs. l5>/ 2 lbs.

No. 300,000 C.M. Copper Strd. (.629") No. 1/0 B. a S. Copper Solid (.325")

No. 4/0 A.C.S.R. (.563") No. 2 A.C.S.R. (.316")

1628-168 As above but bronze lined jaws for strandeJ conductors.

1628-16BP As 1628-16 but jaws extra width and bronze lined—for larger cables.

No. 550,000 C.M. Copper Strd. (.853") No. 1/0 B. a S. Copper Solid (.325") 1.06 in. 15,000 lbs. 17 lbs.

No. 477,000 C.M. A.C.S.R. (.883") No. 2 A.C.S.R. (.316")

Bronze lining of jaws prevents slippage and consequent surface abrasion of strand.

These grips successfully fill a long felt want
taking the heavy loads incident to larger
strands without injury to the strand itself.
Forged from alloy steel heat treated. Grip¬
ping jaws are machined smooth. Rivets are

machine turned and workmanship through¬
out is first class.

These grips frequently can be modified to
accommodate cables of larger diameters.
Write us on your special requirements.

Whether used on solid or strand (galvanized, copper or aluminum) it is always important to keep
the jaws of grips clean and free from any grease, accumulation of spelter or other metal which
may be deposited in the grooves. This will prevent slippage and insure full efficiency.

14

GENUINE KLEIN TOOLS

KLEIN'S "CHICAGO" GRIP Tackles and Hand Lines

For Hollow Core and other large diameter Conductors and Cables

CAT. No.

I628-30B

1628-40B

MINIMUM
CABLE SIZE

APPROX

OPENING

1,000.000 C.M. Hollow Con¬
ductor (1.257")

1,250,000 C.M. Copper
Strand (1.288")

1,033,500 C.M. A.C.S.R.

(1.245")

350,000 C.M. Hollow Con¬
ductor (1.00")

550,000 C.M. Copper
Strand (.853")

477,000 C.M. A.C.S.R.

(.883")

1.35 in.

1,250,000 C.M. Hollow Con- 1,000,000 C.M. Hollow Con- 1.60 in.

ductor (1.430") ductor (1.257")

1,750,000 C.M. Copper 1.250,000 C.M. Copper

Strand (1.525") Strand (1.288")

SAFE

LOAD

20,000 lbs.

25,000 lbs. 32 lb*.

1,590,000 C.M. AC.S.R.

(1.545")

1,033,500 C.M. A.C.S.R.

(1-246”)

KLEIN'S HOWES WIRE TOOLS

No. 1702

The swivel hook is forged steel with an open¬
ing large enough to go ’round an insulator
CAT. No. size

1702-20 Single purchase.

pin or other convenient object. The shank
of hook is lengthened out so as to reach
under D. P. insulator when necessary. The
forward end has a locking device to hold
the load at any distance. It is arranged so
that a grip can be attached. All metal parts
are galvanized finish.

WEIGHT EACH

2l/ 2 lbs.

Strap H/j-inch wide, 7 ft. long

KLEIN'S "CHICAGO" LINEMEN'S TOOL

No. 1700-30

This set is a combination of “Chicago” Grip
No. 1613-30 with Howes Wire Tool No. 1702-
20. It is largely used by telephone compa¬
nies. Detailed description of Grip and Wire
Tool are given under their indivdual catalog
numbers.

Other sizes of grips can be furnished in this
combination to order only.

Bronze lining of jaws prevents slippage and consequent surface abrasion of conductor.

CAT. No.

1700-30

For No. 6 wire and smaller down to No. 13

WEIGHT EACH
... 4 lbs.

In the case of hollow conductors and other
large diameter cables the jaws of the grip
must be shaped to provide maximum enclos¬
ure and contact with the circumference of
the cable itself. When so made the grip will
function at maximum efficiency. Slippage is
prevented and danger of crushing or collaps¬

ing hollow conductors is avoided. For the
above reasons we hold the grips in blank
and finish as necessary for any particular
requirement.

These Grips are forged from alloy steel—
heat treated. The jaws are bronze lined.

KLEIN'S SELF-LUBRICATING HEAVY BLOCK TACKLES

Consists of two special double sheave blocks.
The spring guarded snap hooks and eye are
drop forgings. The side plates are wrought.
Pulleys are bronze bushed and self lubri¬
cating. Galvanized finish. The rope used is
best quality Manila four strand, spliced to
eye of block with galvanized thimble. Runs
free and does not twist in the way cheaper
ropes do.

CAT. No. WEIGHT EACH

1802-40 Furnished with 30 ft. of l/ 2 -in. best quality Manila rope, 4 strand.15'/, lbs.

1802-50 As above with %-in. rope.17% lbs.

1802-60 As above with %-m. rope.l9/ 2 lbs.

Other lengths of rope furnished to order.

No. 1802

CAT. No.

1604-10

1604-20

KLEIN’S "HAVEN'S" STEEL GRIPS

WEIGHT
PER DOZ.

12 lbs.
28l/ 2 lbs.

These popular grips have been improved in
design and materials. All parts solid steel
drop forgings, heat treated as necessary for
maximum strength and service. The eye is
pear shaped (7/s inch and 1/s inch wide
respectively) and a roller fitted to the body

yoke makes the motion free and allows the
load to come on smoothly. Instantaneous
hold, yet a shake on the tackle rope releases
the grip. These grips will not slip due to
the hand cut serration in the face of the
eccentric. Galvanized finish.

)

KLEIN'S IMPROVED "HAVEN'S" GRIP

APPROXIMATE

MIN. OPENING DESCRIPTION

7/32 in. (.22 in.) For wire* % in. to No. 6 B & S

SAFE

LOAD

8000 lbs.

CAT. No. MAX. OraNINU

1625-20 25/32 in. (.78 in.)

This grip is another improved design. All
the desirable features have been retained,
but by the use of alloy steel drop forgings
properly heat treated the weight has been
reduced over forty per cent at the same time
the safe load rating has been increased sixty
per cent. Suitable for use on solid or strand
wires. The swing latch engages stud on the
lower jaw preventing any distortion of the
body or cross bolt under load. This grip is
a favorite for use on trolley wire and
weatherproof. It can be readily adapted at

slight extra cost for hot line work on
weatherproof (insulated) conductors. The
swing latch holds the tool on the line in
position for the pull.

The handle or draw piece works smoothly
against steel roller set in yoke of body arm.
The eye is pear shaped 1% inch wide, per¬
mitting use of oversized sister hook on the
tackle. Hand cut serration in face of ec¬
centric assures a hold that cannot slip. Al¬
most automatic in action. Galvanized finish.

KLEIN'S SELF-LOCKING BLOCK TACKLE

Consist of light steel shell blocks galvanized,
fitted with a snubbing hook to lock load in
any position. This is a great convenience and
time-saver for the man on the pole. Also in
handling a vertical load. To lock the load,
simply pull the luff rope under the hook. To
release, simply pull the rope. The blocks are
arranged with spring guard snap hooks.

When pulling up wire to make a splice it
may be used with two grips attached to the
snaps, or with the drop forged hook No. 258
to anchor to an insulator-pin or other con-

CAT. No.

1802-30 Furnished with 25 ft. %-in. 4 strand Manila rope

No. 1802

venient anchorage. (The hook is specially
shaped to fit under D. P. insulator on cross
arm.) The rope is best quality and will not
twist as the cheaper grades do.

(Shipped un-assembled.)

WEIGHT EACH

and detachable anchor hook (*No. 258) 3 lbs.

KLEIN'S SELF-LOCKING BLOCK TACKLE

(With Guarded Snaps)

The No. H-1802-30 set of blocks is identical
with the No. 1802-30 set described above ex¬
cept that the snaps are “guarded.” To ac¬
complish this feature the nose of each hook
has been lengthened to extend over the latch
or keeper. This does away with any neces¬
sity of taping the snaps after come-a-long
has been engaged.

No. H-1802

CAT. No. WEIGHT EACH

H-1802-30 Furnished with 25 ft. %-in. 4 strand Manila rope and detachable hook (*No. 258) . 3(/ 2 lbs.

KLEIN'S ANCHOR HOOK FOR TACKLES

This hook is a solid steel drop forging. It
is approximately 5% inches overall length
x 3*4 inches across the hook. The eye has
an inside diameter of $4 inch to engage with
snap on Klein Tackles 1802-30 and H1802-30.
Galvanized finish.

Specially shaped to slip under D. P. insu¬
lator and engage insulator pin on cross arm.

CAT. No.

*258 Drop Forged Hook. 2 in. Opening. % in eye

4 lbs.

15

GENUINE KLEIN TOOLS

KLEIN'S HAND LINE

With Drop Forged Snap Hoolc No. 443-A

No. 1803

1803- 60 With 75 ft. %-in. best quality Manila rope, 4 strand and No. 443-A Snap .... 3*A lb*.

1803-120 As above with 120 ft. of rope and No. 443-A Snap.

These lines are designed for maximum safety
and service. The rope is best quality and
does not twist. It will far outlast cheaper
material. Spliced to eye of snap hook with
galvanized steel thimble. The snap hook is
drop forged and similar to those used on

safety straps except that it has round eye.
It opens to inch.

Can be furnished with any different length
of rope to order.

(For details of snap see next item.)

KLEIN'S SNAP FOR HAND LINES AND LIGHT HOISTS

No. 443-A

CAT. No.

443-A Forged Snap. Eye I-1/16 in. I. D. Length overall 5|/j ir

WEIGHT PEB DOZ

. . . 6l/ 2 lbs.

This snap is used on hand lines, 1803 series.
It will be found a real convenience for many
uses. Can be used on all light hoisting—for
roofers, etc. Galvanized Finish. The hook
and eye are an integral drop forging. Duck
bill nose closes around latch.

Will carry loads up to 1250 lbs.

When fitted to a 4 inch tackle block this
hook provides an ideal means for connecting
with come-along; no taping is necessary.
The opening will take up to Y inch.

LIST OF PARTS FOR KLEIN'S

Catalog No. 3529 with Pump in

FURNACES

Fount

KLEIN FURNACE ASSEMBLY

Wheel Assembly
803 Burner Assembly
804 A Furnace Pump with
Locking Device
Assembly

805 Orifice Cleaning
Needle Assembly
815 Generator Coil

Assembly Complete

WHEN ORDERING
SPECIFY PART
NUMBER OF PIECE
REQUIRED

KLEIN'S FURNACES AND TORCHES

Construction throughout is sturdy and sim¬
ple. The materials are the best.

The principal consideration in the produc¬
tion of these tools has been to meet the ex¬
acting requirements of utility companies
with maximum safety.

The Klein Furnaces operate on either gaso¬

line or kerosene without any change of parts.
Once accepted as standard a small stock of
replacement parts will enable a handy man
to maintain the equipment in service without
the interruptions and expense necessary if
return to factory were required.

KLEIN'S FURNACE

U. S. Patent No. 1.307,213

CAT Made for Safety and Service weight each

3529 Gasoline-Kerosene Furnace, Pump in fount with windshield No. 3010 . 20l/ 2 lbs.

Shipped with Windshield No. 3010 as shown unless otherwise ordered.

These furnaces are of sturdy construction with a minimum of parts and are especially made
to stand up to the field requirements of Public Utility Companies. They are well suited for
general use where quality and safety is desired. Quick starting is ensured by multi-coil
burner which is economical and vaporizes the fuel thoroughly, producing an intensely hot
fire. Simple cleaning device to remove carbon deposit without taking burner apart. One
gallon capacity tanks formed of heavy gauge steel with bottom rolled in — no chance for
leaks due to wear. All fittings brazed. Furnished with pump in fount. These furnaces are
used exclusively by many of the largest properties.

Either gasoline or kerosene may be used without making any change in burner.

LIST OF PARTS FOR KLEIN'S TORCHES

808-C

TORCH

HEAD

ASSEMBLY

Catalog No. 3428
with Pump in Handle

Catalog No. 3428-C
with Pump in Handle and
Coil in Torch Head

247 Spring

709 Air Valve Cork Shell

710 Air Valve Container
Guide

711 Air Valve Compression
Spring

714 R. H. Rivet (% x tf)
716 Air Valve Cork
721 Hand Wheel
733 Handle Bar Casting-
Upper

767 734 Handle Bar Casting-
Lower

739A Pump Button

752 Feed Nipple

753 Intake Feed Tube

754 Torch Head

756 Torch Head and Feed
Valve Packing Nut

758 Torch Head Stem

759 Torch Head Windshield
763 A Pump Top End Piece
767 Brass Set Screws

768 A Pump Rod

771 Brass Washer

772 Soldering Iron Holder

773 Brass Screw

775 Filler Cap Cork Washer
779 Hexagon Nut

783 Brass Burr

784 Torch Head Burner Tip

785 Leather Washer

786 Pump Cylinder and
Check Bottom Assembly

791 Generator Cup
800 Filler Cap and Plug
Assembly

807 A Torch Pump with

Locking Device Assembly
808 Torch Head, Regular,
Complete

808 c Torch Head with Coil,
Complete

812 Torch Head Coil
Assembly

813 Torch Head Nozzle

WHEN ORDERING
SPECIFY PART NUMBER
OF PIECE REQUIRED

16

GENUINE KLEIN TOOLS

KLEIN'S TORCHES

KLEIN'S COMBINATION STEEL LAG SCREW WRENCH

U.5. PAT. H9 1.676.352

No. 3428

No. 3428-C

CAT. No. SIZE WEIGHT EACH

3428 One Quart. Pump built in.5>/ 2 lb*.

Specially designed for requirements of Public Utility Com¬
panies, at the same time a most satisfactory torch for general
use.

Has double length generating channels for quick starting.
Flame is intensely hot, easily regulated from minimum to full
blast.

Will not back generate. Clean out plugs at all angles. Needle
has positive shoulder stop which prevents damage to burner
by enlarging orifice.

Pump well made and sturdy. Tank heavy gauge copper.
Capacity one quart.

CAT. No. SIZE WEIGHT EACH

3428-C One Quart. Pump built in. Sy 2 lb*.

This torch is similar in construction to No. 3428, but has
different head with coil burner. “Carbon Choke” nuisance is
done away with. Fuel vaporizes rapidly so it burns as a dry
gas with intensely hot flame.

For outdoor use this torch is ideal—will not blow out even
in a gale of wind.

The burner coil and burner tip are both readily replaceable
at slight expense.

KLEIN'S TORCH HEAD (COIL)

CAT. No. WEIGHT EACH

808-C Complete .I'/j lb*-

This assembly comes complete ready to install on conventional
torch and convert it into a “coil burner” with all the advan¬
tages of this construction.

CAT. No. SIZE WEIGHT PER DOZ.

3109-20 131/2-inch.24 lb*.

This wrench is forged from select bar steel.
The slot is formed in a cross shape and will
fit machine bolts, nuts or lag screws from %
inch to 34 inch. The small end of the wrench
is arranged for square nuts on A inch
machine or carriage bolts. The round hole
allows the end of a bolt to come through as

the nut is run on.

The jaw is wider at its lower portion than at
the entrance and when this wrench is put on
a nut or bolt the tendency is to draw the bolt-
head or nut into the wrench and prevent slip¬
ping off, a most desirable advantage original
with this wrench and a real “safety” feature.

KLEIN'S LINEMAN'S WRENCH

"Bell System" Type

CAT. No. SIZE WEIGHT PER DOZ.

3146 13-inch, for % in. hardware .... 23 lb*.

This wrench is forged of select bar steel, heat
treated, and is of the open end type with
two openings of different size at each end.
There is a hole provided at the larger end
so that the wrench may be used for turning
in standard pole steps.

This wrench is particularly adapted for use
on the heavier 3-bolt guy clamps on which

the clearance for a wrench is limited and is
generally suitable for 34 inch hardware.
Openings:

Large end 1J4 inch and inch
Small end inch and 34 inch
(For 34 inch through bolt, l / 2 inch lag screw,
% inch carriage bolt, *4 inch and 34 inch guy
clamps.)

SHIELD FOR KLEIN FURNACE

(One of these shipped with each furnace unless ordered otherwise.)

Made of heavy gauge sheet steel. The top edge is rolled and
the bottom is reinforced with a heavy ring. All joints
welded. Diameter at top 9 inches.

CAT. No.

3010 For

Furnace No. 3529

WEIGHT EACH

. . . 3 1b*.

KLEIN'S LINEMAN'S WRENCH

CAT. No. SIZE WEIGHT PER DOZ.

3146-A 13-inch, for % in. hardware.23 lb*.

CAT. No. SIZE WEIGHT PER DOZ.

3146-A 13-inch, for % in. hardware.23 lb*.

Same as No. 3146 but modified for 3$ inch hardware.

Openings: (For 34 inch and 34 inch through bolt, J4

Large end inch and 1A inch inch lag screw, % inch carriage bolt, 34 inch

Small end 34 inch and J4 inch and 34 inch guy clamps.)

'STAYSALITE" LINEMEN'S TORCH

The ”Sfay*alite" Torch ha* these main feature*:

It “Staysalite” in a wind. It is light; it is small. It is lit and
extinguished in a moment, as wanted. It bums alcohol without
odor or noise. It has no adjusting parts, therefore it cannot ^et out
of order. It is carried in the lineman’s belt and does away with the
ground man. It is hung directly on the wire under the joint to be
soldered. It can be used as a small heater or soldering iron. It is
provided with a cup for holding soldering paste.

This Torch is the invention of a practical, experienced telephone
man. For hot work within the range of the light work of the tele¬
phone or telegraph lineman, house wireman and general shop man
it is a boon.

To suspend the torch on a wire under a joint, place the wire in the
slots on the upper edge of the rim, give the body of the torch a
half turn and it’s on; when through, give it a half turn in the
opposite direction and it’s off. Drop it back in your belt by means
of the hook and you are free for the next thing in line. In general
use by many of the largest utility corporations in the country.

CAT. No.

3420 .

WEIGHT EACH

. . |l/ 4 lb*.

FOLDING WINDSHIELDS

This shield is a folding
design made of heavy
galvanized sheet steel in
four leaves each 24" high
by 18" wide hinged to¬
gether, the hinges being
securely riveted. The
grate is made of A" x
34" steel, welded and
swings on one leaf of the
shield.

In use this grate is
brought up to a horizon¬
tal position where it is
held firmly in two clips
riveted to the leaf of the
shield opposite the one
from which it is perma¬
nently suspended.

All hinges, handles, lugs and brackets are
riveted and cannot come loose. The grate is
designed so that it can be used with melting
pot or the larger sizes of wax kettles. The
shield can be folded as shown for conveni¬
ence in transportation and when closed is
held in place by a swing latch at the top.

This shield is recommended not only to im¬
prove the burning of the furnace by protect¬
ing it from wind, but also because it provides
a means of safety to the public when fur¬
naces are being operated in crowded dis¬
tricts.

3020 Folding Windshield* for use with furnace*. 24 in. high x 18

WEIGHT EACH

n. square, with welded grate. 42 lbs.

KLEIN'S "CHICAGO" FISH-TAPE PULLER

Patent No. t.62*744

Here is a simple, husky come-along for Fish-Tape.

To engage puller on fish-tape place the tape sideways in slot and
give puller a slight forward motion while pushing tape deeper into
the slot. (This slips tape under the ratchet wheel.) Now pull. You
have a positive grip on the tape. Slide forward on tape to position
for new bite.

Klein’s “Chicago” Fish-Tape Puller grips like a vise—never slips
—simple, strong, automatic.

Does not injure the tape, 334 inches long, can be carried in the
pocket.

Saves time and protects the hand.

(We do not supply Fish-Tape.)

CAT. No.

1629 For Standard Fi*h Tape*

1629-A Modified for No. 12 Iron

WEIGHT PER DOZ.

. . . . 21/, lb*.
. ... V/ 2 lbs.

KLEIN'S "FAVORITE" TREE TRIMMER HEAD

This trimmer, as its name im¬
plies, is a favorite among users.
The head is one piece and com¬
prises the hook portion with
which the knife engages and the
socket into which the handle is
inserted. This socket is perfect¬
ly straight, eliminating the ne¬
cessity of tapering the end of
the handle. The knife is forged
from tool steel and is integral
with the lever and the cutting
edge is carefully tempered and
ground making it very effec¬
tive. This trimmer will sever a
1-inch branch. The knife is held
open by a flat steel spring and
is operated by a rope attached to
the end of the lever.

Two threaded holes are provided
for attaching a saw. See cut No.
3600-21.

CAT. No.

3600-20 Head only. No saw, rope or handle . .

3600-21 Head with straight taw. No rope or handle
3600-22 Head with curved taw. No rope or handle

SIZE WEIGHT EACH

17“

23”

31/2 lb*.

41b*.

26” 4 I /4 lb*.

17

GENUINE KLEIN TOOLS

No. 3628 KLEIN'S TREE TRIMMER HEAD

ROTARY KNIFE

The design of this trimmer differs from any
other. The entire head, comprising hook
and socket, into which handle fits is sturdily
constructed of pressed steel. The knife,
made of tempered tool steel, is round in
shape and arranged to rotate slightly with
each cut, thus providing the entire circum¬
ference of the blade for cutting and giving
an edge more than three times the length of
that on the ordinary blade.

The leverage makes this trimmer cut easily
limbs up to 1J4 inch, both green and dry.
Knife may be readily removed for sharpen¬
ing or renewal.

Two threaded holes are provided for attach¬
ing saws shown in this catalog.

SIZE WEIGHT EACH

No saw, rope or handle. 12(/j-inch.3 lbs.

CAT. No.

3628 Head only.

No. 3628-K

CIRCULAR KNIFE FOR TREE TRIMMER

This knife is made of first quality tool steel oil tempered. Diameter 2
inches. Hole at center y 2 inch diameter. Double bevel for easy cutting.

CAT. No. WEIGHT PER DOZ.

3628-K Circular Knife, 2 % in. diameter.2 lbs.

KLEIN'S TREE TRIMMER SAWS

No. 913-12

CAT. No. SIZE

913-12.12 in.

913-15.15 in.

No. 913-15

WEIGHT PER DOZ.

. . . 41/, lbs.
. . . 4% lbs.

Teeth set to cut on up
and down stroke.
Readily attached to
tree trimmer. The
curved blade saw is
particularly efficient
and easy cutting even
for large limbs.

No. 913-G

No. 913-G KLEIN'S SAW HANDLE

CAT. No. WEIGHT PER DOZ.

913-G.4l/ 2 . lbs.

When a hand saw is required either of the tree trimmer saws shown
above can be set in this handle in a few seconds and held securely with
a single thumb screw. Makes an efficient hand saw for cutting heavy
branches.

KLEIN'S "XELA" ELECTRICIAN'S KNIFE

A Handy Combination for the Electrician.

No. 1550-2

1550-2 Double Blade

The blades of this knife are made of high
grade cutlery steel carefully tempered.

The locking feature on the screw-driver
blade is simple and of such construction that
it does not wear out.

It automatically locks the blade when open,
yet a slight side pressure of the thumb re¬
leases the lock and permits the blade to be
closed readily. Handle of cocobola — hard
and durable.

WEIGHT PER DOZ.

.2 lbs.

KLEIN'S SKINNING KNIFE

(With Insulated Handle)

Here’s a knife linemen have been looking
for. The “half hard” rubber handle is
molded on securely and provides adequate

CAT. No.

1560-3 Length overall 8 in. Blade 3 in.

insulation as well as a good generous grip.
Shouldered out at the blade to prevent ac¬
cidental cutting of glove or finger. The
shape of the blade brings the point below
the curve—a real safety feature. Back of
blade ground flat for scraping. The hole in
the handle is through the solid rubber.
Forged from first quality cutlery steel indi¬
vidually tempered.

See also Knife Pocket No. 5163 made for this
knife.

WEIGHT PER DOZ.

. 41/4 lb*.

KLEIN'S CABLE SHEATH SPLITTING KNIFE

Heavy Duty Type

Blade tempered and ground to keen
edge. Has strong leather handle, se¬
curely riveted. Temper blued finish. A
sturdy knife that will stand up to hard
usage. Length over all 9% inches. Blade
4 y 2 inches.

CAT. No. WEIGHT PER DOZ.

No. 1515-1

1515-1

13 lbs.

KLEIN'S TREE TRIMMER HANDLES

(With Locking Ferrules)

tiiJSEP . 1 “'•••••• M

No. 3605

CAT. No. AVERAGE WEIGHT PER DOZ. SETS

3605-6 One set 18 ft. 3 section* with ferrules.125 lbs.

3605-9 One set 18 ft. 2 sections with ferrules.123 lbs.

KLEIN'S "XELA" ELECTRICIAN'S SCISSORS

A scissor designed for the electrician
and mechanic. Will stand continued
hard service. Made of high-grade steel
properly tempered. Has a screw hinge,
allowing adjustment. Nickel plated fin¬
ish.

CAT. No. 8IZE WEIGHT PER DOZ.

2100-5 5-inch. 2 lbs. No. 2100-5

KLEIN'S INSPECTORS' POCKET TOOL KIT

Handles are 1$4 inches round selected Wash¬
ington Fir turned at ends for ferrules. The
inner ferrules are brass 5 inches long x V/ 2
inches diameter. The outer ferrules are of
seamless steel tubing 7 y 2 inches long—gal¬
vanized.

The brass ferrule carries the -fa inch locking
pin which engages in hole drilled in the

steel ferrule and is held in position by a
concealed coil spring inside the handle. The
locking pin can be depressed readily by
thumb pressure when assembling the handle
sections or taking them apart.

This simple arrangement is practically auto¬
matic and entirely removes any possibility
of handles pulling apart in use.

KLEIN'S TREE TRIMMER HANDLES

(Plain Brass Socket Ferrules)

No. 3601

CAT. No.

3601-6 One set 18 ft. 3 sections
3601-9 One set 18 ft. 2 sections

AVERAGE WEIGHT PER DOZ. SETS

120 lbs.
118 lbs.

Handles are 1% inches round selected Wash¬
ington Fir. A brass ferrule 7 inches long x
1 y inches diameter is permanently attached

at upper end of section. The lower end
of each section is turned to fit into the brass
ferrule for 3 x / 2 inches.

Solid black leather folding case
strongly stitched, reinforced back.
Fitted with one each of the following
tools.

201-6 Side Cutting Plier.

301-5 Long Nose Plier.

1550-2 “Xela” Electrician’s Knife.

1 Pair Electrician’s Tweezers.

1 Special File.

1 Insulated Screwdriver.

A very handy assortment to fit the
pocket.

Size closed 6%" x 3%" x 1%".

CAT. No. WEIGHT EACH

1305-2 . 11/4 lbs.

No. 1305-2

KLEIN'S POCKET TOOL ROLL

Just the tool you want—right where you want it. This new
handy kit designed for mechanics, service men, electricians
or any man who is proud of good tools. Keratol Roll with
strap and buckle. Size rolled 8" x 2 y 2 ” diameter.

No. 1305-33A

Comprises the following:

1 No. 201-6 N.E. Side Cutting Plier
1 No. 301-6 Long Nose Plier
1 No. 202-5-A Oblique Cutting Plier

1 No. 1550-2 Electrician’s Knife
1 File

1 Pair Electrician’s Tweezers
1 Insulated Screw Driver

CAT. No.

1305-33-A

WEIGHT EACH
. . |l / 2 lbs.

18

CATALOG No. 39-NET PRICE LIST

Effective April 1, 1939

Prices subject to change without notice

Page Catalog No.

r 201-5
201-6
201-7
201-8
201-9

212-6

212-7

212-8

201-5-NE

201-6-NE

201-7-NE

201-8-NE

201-9-NE

21 2-6-NE
21 2-7-NE
21 2-8-NE

202-5

202-6

245-5

245-5-W

240-5-S

240-5 .

240-6 .

202-5-SW

202-5-A ..
202-6-A ..

242-6 .

220-7 .

232-5^ ..
232-7 .

235-6

301-5
301-6
V 301-7

Section No. 1—Klein Pliers

Net Price

List

Page

Catalog No.

Net Price

List

-Ea. $2.30

'203-5 .

.Doz. $1 6.40—

-Ea. $2.05

. —Doz.

19.60...

-Ea.

2.45

203-6 .

.Doz.

18.40-

-Ea.

2.30

—Doz.

22.40-

-Ea.

2.80

203-7 .

.Doz.

20.00-

-Ea.

2.50

...Doz.

24.00...

..Ea.

2.95

...Doz,

30.40-

..Ea.

3.80

303-6 .

14.80-

-Ea.

1.85

22 40

Ea.

2.80

3 <

317-6 .

....Doz.

1 4.80-

-Ea.

1.85

...Doz,

24.00...

...Ea.

3.00

...Doz.

30.40-

-Ea.

3.80

217-6 .

.Doz.

1 8.40—

...Ea,

2.30

....Doz,

1 8.40-

...Ea.

2.30

^ 31 3-6 .

.Doz.

21.20-

...Ea.

2.65

. .Doz.

1 9.60-

...Ea.

2.45

r305-6 .

16.40-

-Ea.

2.05

.Doz.

22.40-

...Ea.

2.80

.Doz.

24.00-

...Ea.

2.95

206-6 .

.Doz.

1 8.00-

-Ea.

2.25

_Doz.

30.40-

...Ea,

3.80

31 1 -554 .

1 8.00-

-Ea.

2.25

.Doz.

22.40...

...Ea.

2.80

.Doz.

24.00-

...Ea.

3.00

304-6 .

.Doz.

1 6.40-

-Ea.

2.05

30.40-

...Ea.

3.80

205-6 .

.Doz.

1 8.00-

-Ea.

2.25

...Doz,

1 6.00-

...Ea.

2.00

_Doz.

1 7.20-

-Ea.

2.15

A J

302-6 .

1 9.60-

-Ea.

2.45

16.00-

...Ea.

2.00

4 1

316-S .

.Doz.

18.00-

-Ea.

2.25

_Doz.

18.80-

...Ea.

2.35

301 -C .

.Doz.

18.00-

-Ea.

2.25

...Doz,

1 8.00-

...Ea.

2.25

039 .

.Doz.

22.40-

-Ea.

2.80

.Doz.

17.20-

-Ea.

2.15

203-8 .

.Doz.

28.40-

—Ea.

3.55

18.40-

...Ea.

2.30

203-8-N

.Doz.

30.40—

-Ea.

3.80

.Doz.

19.20-

...Ea.

2.40

w 301 -6-VP .

....Doz,

20.40-

-Ea.

2.55

_Doz.

1 6.00-

—Ea.

2.00

f 202-5-VO .

.Doz.

21.60-

—Ea.

2.70

.Doz.

17.20-

....Ea.

2.15

202-5-VC .

.Doz.

20.80..

—Ea.

2.60

1 7.60-

....Ea.

2.20

202-5-AV .

.Doz.

1 8.40-

-Ea.

2.30

.Doz.

1 8.40-

....Ea.

2.30

245-5-V .

.Doz.

18.40-

-Ea.

2.30

_Doz.

26.00-

„„Ea.

3.25

29.20-

—Ea.

3.65

5 <

301-5-V .

....Doz.

1 8.00-

—Ea.

2.25

25.60-

—Ea.

3.20

203-5-V .

....Doz.

20.40-

—Ea.

2.55

13.60-

—Ea.

1.70

406-654 .

.Doz.

1 0.00-

—Ea.

1.25

.Doz.

1 4.80-

—Ea.

1.85

407-7 .

12.00-

....Ea.

1.50

.Doz.

1 6.40-

—Ea.

2.05

. 408-8 .

.Doz.

1 4.00-

—Ea.

1.75

Section No. 2—Splicing Clamps

Page Catalog No. Net Price

r 102-1 Ea. $2.50

102-3 .Ea. 3.20

102-30 .Ea. 3.20

102-48 .Ea. 3.20

105-15 .Ea. 2.65

6< 105-17 . Ea. 3.20

105-31 .Ea. 2.65

132-15 .Ea. 4.55

132-46 .Ea. 4.55

132-12 ..Ea. 3.35

w 132-30 .Ea. 4.55

* 132-48 .Ea. 5.30

132-39 . Ea. 4.55

m J 132-47 ..Ea. 5.30

' A 132-74 . Ea. 5.30

107-20 _ Ea. 10.30

w 107-34 .Ea. 15.00

Section No. 3—Climbers

Page Catalog No. Net Price

^ 1 939 .Pair $4.00

1900 .Pair 3.60

1901 .-.Pair 3.60

1903 .Pair 3.60

8 < Regaffing above

Climbers ...Pair 2.25

1 907 .-.Pair 4.00

Regaffing Tree
Climbers ....Pair 2.75

Section No. 4 —Leather Goods

Page Catalog No. Net Price

N.O. 1 Neatsfoot oil

q ^ Pint .Ea. $ .75

N.O. 2 Neatsfoot oil

Quart .Ea. 1.25

Section No. 4 —Leather Goods
(Continued)

Page Catalog No. Net Price

^N.O. 4 Neatsfoot oil

Half Gallon .Ea. $2.25

5301-1 ..Set 3.55

5301-2 .Set 3.75

5301-3 . Set 3.75

5301-11 .Set 3.45

5301-12 . Set 3.65

9^ 5301-13 .Set 3.65

5301-6 . Set 3.95

5301-7 .Set 4.10

5301-8 .Set 4.10

5301-4 .Pair 1.45

5301-9 .Pair 1.40

5301-14 .-Pair 1.60

5301-10 .Pair 1.55

V

Section No. A —Leather Goods
(Continued)

Page

10 <

11 <

12 <

Catalog No.

Net Price

5301-5 .

.Pair $2.10

5301-15 .

.Pair

2.05

5301-16 .

.Pair

1.80

5301-26 .

.Pair

1.60

8200 .

.Pair

.85

8201 .

.Pair

.85

8202 .

.Pair

.65

8206 .

.Pair

.70

8203 .

.Pair

1.00

8204 .

.Pair

1.15

8205 .

.Pair

1.15

1929-G .

.Pair

.35

5228 .

.Ea.

8.75

H-5228 .

.Ea.

8.75

5204-TSO .

.Ea.

7.65

H-5204-TSO .

.Ea.

7.65

5204-DE .

.Ea.

6.60

H-5204-DE .

.Ea.

6.60

5204 .

.Ea.

5.10

H-5204 .

.Ea.

5.10

5205 .

.Ea.

5.60

H-5205 .

.Ea.

5.60

5202 .

.Ea.

4.75

H-5202 .

.Ea.

4.75

521 1 .

.Ea.

6.25

H-5211 .

.Ea.

6.25

5221 -KK .

.Ea.

6.45

H-5221-KK .

.Ea.

6.45

5212 .

.Ea.

5.50

5214 .

.Ea.

3.85

5214-0 .

.Ea.

3.75

5206-1-A .

.Ea.

9.60

5209 .

.Ea.

6.70

5227-KK .

.Ea.

4.60

H-5227-KK .

.Ea.

4.60

KL-5251 .

.Ea

5.35

5251 .

.Ea.

4.85

H-5251 .

.Ea.

4.85

KL-5250 .

.Ea.

5.35

5250 .

.Ea.

4.85

H-5250 .

.Ea.

4.85

5215 .

.Ea.

2.55

H-5215 .

.Ea.

2.55

KL-5253 .

.Ea.

6.70

5253 .

.Ea.

6.20

H-5253 .

.Ea.

6.20

5257-S .

.Ea.

6.50

5257-L .

.Ea.

6.85

KL-5258 .

.Ea.

7.20

5258 .

.Ea.

6.70

H-5258 .

.Ea.

6.70

KKD-025 .

.Ea.

.25

KL-5233 .

.Ea.

5.35

5233 .

.Ea.

4.85

H-5233 .

.Ea.

4.85

KL-5234 .

.Ea.

4.15

5234 .

.Ea.

3.65

H-5234 .

.Ea.

3.65

Section No. 4—Leather Goods
(Continued)

Page

Section No. 6
Tackles and Hand Lines

13 <

Catalog No.

Net Price

KL-5236 .

.Ea.

$ 2.10

5236 .

.Ea.

1.85

H-5236 .

.Ea.

1.85

5130 .

. Ea.

.20

5131 .

. Ea.

.25

5132 .

.Ea.

.20

5139 .

.Ea.

.75

5163 .

.Ea.

.85

51 1 8 -K .

.Ea.

1.25

5118-S .

.Ea.

1.05

51 1 8 -R .

.Ea.

1.25

51 1 1 .

. Ea.

1.00

51 1 6 .

. Ea.

1.50

5107 .

. Ea.

.65

51 12 .

. Ea.

.85

5120-9 .

. Ea.

2.00

5120-15 .

. Ea.

2.65

5108-14 .

. Ea.

7.50

5108-16 .

. Ea.

8.00

5108-18 .

. Ea.

8.50

5108-20 .

. Ea.

8.75

5108-22 .

. Ea.

9.25

5108-24 .

. Ea.

9.75

5102-12 .

. Ea.

4.15

5102-14 .

.Ea.

4.50

5102-16 .

.Ea.

5.00

5102-18 .

.Ea.

5.25

5102-20 .

.Ea.

5.75

5102-22 .

.Ea.

6.25

5102-24 .

. Ea.

6.75

5105-16 .

. Ea.

5.25

5105-18 .

. Ea.

5.50

5105-20 .

.Ea.

6.00

5105-22 .

.Ea.

6.50

5105-24 .

.Ea.

7.00

/

14 <

Section No. 5—Grips

Page Catalog No. Net Price

' 1 61 3-30 .Ea. $2.00

1 61 3-30-B ..Ea. 3.35

1613-40 .Ea. 3.55

1 61 3-40-B .Ea. 6.00

1613-50 .Ea. 6.00

1 61 3-50-B .Ea. 10.00

1 61 3-50-A .Ea. 6.00

1 61 3-50-AB Ea. 10.00

1611-20 .Ea. 3.35

1611-30 ....Ea. 4.20

1611-40 .Ea. 6.65

1611-50 .Ea. 6.65

1 628-5-B .Ea. 8.75

1628-5 ..Ea. 7.00

1626-39 . Ea. 8.90

1 626-39-B .Ea. 11.35

1626-40 Ea. 8.90

1 626-40-B .Ea. 11.35

1626-AB .Ea. 14.45

1628-6 . Ea. 11.20

1 628-6-B Ea. 14.95

1628-16 .Ea. 20.00

1 628-1 6 -B .Ea. 23.35

1628-16-BP _ Ea. 26.65

1 628-30-B .Ea. 60.00

1 628-40-B .Ea. 63.35

1604-10 .Ea. 1.90

1604-20 .Ea. 2.80

1625-20 ..Ea. 6.55

15

Page

Catalog No.

Net Price

1702-20 .

.Ea. $5.00

Strap for

above .

.Ea. 2.00

1 700-30 .

.Ea. 7.05

Strap for

Above .

.Ea. 2.00

1802-40 .

.Ea. 10.35

1802-50 .

.Ea. 1 1.65

1802-60 .

.Ea. 12.20

1802-30 .

.Ea. 3.60

PARTS FOR ABOVE

15 \

16

{:

258 .

.Ea.

.75

25 ft. Rope .. .Ea.

.75

267

Plain Block

only .Ea.

1.35

268

Snubbing

Block only....Ea.

1.65

H-1 802-30 .Ea.

4.15

PARTS FOR ABOVE

258 .

.Ea.

.75

25 ft. Rope ....Ea.

.75

H-267

Plain Block

only .Ea.

1.75

H-268

Snubbing

Block only....Ea.

2.25

258 .

.Ea.

.75

1803-60

.Ea.

4.25

1803-120 .Ea.

5.60

443-A ...

.Ea.

1.25

Section No. 7
Furnaces and Torches

Page Catalog No. Net Price

3529 .Ea. $20.00

Parts for Furnace No. 3529

16 <

Part No.

247 .

.Doz.

.35

702-B .

.Ea.

1.25

703 .

.Ea.

.35

705 .

.Ea.

1.45

709 .

.Ea.

.15

710 .

.Ea.

.10

711 .

.Doz.

.35

71 2

.Ea.

.20

713 .

.Doz.

.35

714 .

.Doz.

.35

715 .

.Ea.

.25

716 .

.Doz.

.35

718 .

.Ea.

.70

719 .

.Doz.

.70

720 .

.Ea.

.15

721 .

.Ea.

.15

722 .

.Ea.

.10

723

.Doz.

.70

724

.Ea.

.90

728

Ea.

.15

736-A .

.Ea.

.20

737-A .

.Ea.

.10

738 .

.Doz.

.35

739-A .

.Ea.

.45

756 .

.Ea.

.15

769 .

.Ea.

.15

775 .

.Doz.

.35

776 .

.Ea.

.15

777 .

.Doz.

.35

778 .

.Doz.

.70

779 .

.Doz.

.35

780 .

.Doz.

.35

Section No. 7
Furnaces and Torches
(Continued)

Page

16 <

Part No.

Net Price

781 .

.15

782 .

.Doz.

.35

797 .

.Doz.

.35

798 .

.Ea.

.55

799 .

.Doz.

.35

800 .

.Ea.

.45

802 .

.Ea.

1.35

803 .

.Ea.

.85

804-A .

.Ea.

2.90

805 .

.Ea.

.25

815 .

.Ea.

2.45

Catalog No.

3428 .

.Ea. 1

3.35

3428-C .

.Ea. 1 4.25

808-C .

.Ea.

7.65

PARTS FOR TORCHES
Nos. 3428 AND 3428-C

Part No.

247 .

.Doz.

.35

709 .

.Ea.

.15

710 .

.Ea.

.10

711 .

.Doz.

.35

714 .

.Doz.

.35

716 .

.Doz.

.35

721 .

. Ea.

.15

733 .

.Ea.

.15

734 .

.Ea.

.45

739-A .

.Ea.

.45

752 .

Ea

.25

Section No. 7
Furnaces and Torches
(Continued)

Page

16 <

V

Part No.

753 .

754 .

Net Price

.Ea. $ .15

.Ea. 1 .85

756 .

.Ea.

.15

758 .

.Ea.

.20

759 .

.Ea.

.45

763-A .

.Ea.

.25

767 .

.Doz.

.35

768-A .

.Ea.

.15

771 .

.Doz.

.35

772 .

.Doz.

.70

773 .

.Ea.

.10

775 .

. Doz.

.35

779 .

. Doz.

.20

783 .

. Doz.

.20

784 .

.Ea.

.25

785 .

.Ea.

.15

786 .

.Ea.

.70

791 .

.Ea.

.55

ftnn

.Ea.

.45

807-A .

.Ea.

2.20

808 .

.Ea.

5.15

808-C .

.Ea.

7.65

812 .

.Ea.

3.15

813 .

.Ea.

1.75

Catalog No.

3010 .

.Ea.

2.00

3420 .

.Ea.

5.00

3020 .

.Ea.

12.50

Section No. 8—Miscellaneous

Page Catalog No. Net Price

r 3109-20 .Ea. $2.30

3146 .Ea. 2.25

3146-A . Ea. 2.25

1629 . Ea. 1.00

17 S 1629-A .Ea. 1.00

3600-20 .Ea. 4.60

3600-21 .Ea. 5.85

3600-22 .Ea. 5.95

w 209 .-.Ea. 2.30

3628 .Ea.

3628-K . Ea.

913-12 .-.Ea.

913-15 .Ea.

913-G .Ea.

3605-6 .Per Set

3605-9 .Per Set

Jg J 3601-6 .Per Set

3601-9 .Per Set

1550-2 .Ea.

1560-3 ..Ea.

1515-1 .*Ea.

2100-5 .Ea.

1305-2 .Ea.

^ 1 305-33-A .Ea.

5.55

.90

1.25

1.35
.75

6.25

5.35
4.85

4.50

1.35

1.50

1.75

.85

7.50

9.00

.’■j '1 • •

■-